CAUTION: Stresses above those listed in “Absolute Maximum Ratings” can permanently damage the device. This is a stress only rating and operation of the device at
these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
5.
JA
is measured with the component mounted on a low-effective thermal conductivity test board in free air. See
TB379
for details.
6. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
(
Electrical Specifications
PARAMETER
DC CHARACTERISTICS
Driver Differential V
OUT
(No Load)
Driver Differential V
OUT
(with Load)
Change in Magnitude of Driver
Differential V
OUT
for
Complementary Output States
Driver Common-Mode V
OUT
Change in Magnitude of Driver
Common-Mode V
OUT
for
Complementary Output States
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
Input Current (A/Y, B/Z), (Note
15)
Test Conditions: V
CC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
CC
= 5V, T
A
= +25°C,
Note 7
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNIT
V
OD1
V
OD2
V
OD
R = 50Ω (RS-422), (Figure
1)
R = 27Ω (RS-485), (Figure
1)
R = 27Ω or 50Ω, (Figure
1)
Full
Full
Full
Full
-
2
1.5
-
-
3
2.3
0.01
V
CC
-
5
0.2
V
V
V
V
V
OC
V
OC
R = 27Ω or 50Ω, (Figure
1)
R = 27Ω or 50Ω, (Figure
1)
Full
Full
-
-
-
0.01
3
0.2
V
V
V
IH
V
IL
I
IN1
I
IN2
I
IN2
DE, DI, RE
DE, DI, RE
DE, DI, RE
DE = 0V, V
CC
= 4.5 to
5.5V
DE = 0V, V
CC
= 0V
-7V
V
CM
12V
V
CM
= 0V
I
O
= -4mA, V
ID
= 200mV
I
O
= -4mA, V
ID
= 200mV
0.4V
V
O
2.4V
-7V
V
CM
12V
V
IN
= 12V
V
IN
= -7V
V
IN
= 12V
V
IN
= -7V
Full
Full
Full
Full
Full
Full
Full
Full
25
Full
Full
Full
Full
2
-
-2
-
-
-
-
-0.2
-
3.5
-
-
96
-
-
-
-
-
-
-
-
70
-
-
-
-
-
0.8
2
140
-120
180
-100
0.2
-
-
0.4
1
-
V
V
µA
µA
µA
µA
µA
V
mV
V
V
µA
kΩ
Receiver Differential Threshold
Voltage
Receiver Input Hysteresis
Receiver Output High Voltage
Receiver Output Low Voltage
Three-State (High Impedance)
Receiver Output Current
Receiver Input Resistance
V
TH
V
TH
V
OH
V
OL
I
OZR
R
IN
FN6051 Rev.8.00
Sep 20, 2018
Page 4 of 16
ISL8487E, ISL81487L, ISL81487E
Electrical Specifications
PARAMETER
No-Load Supply Current, (Note
8)
Test Conditions: V
CC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
Here are some new job opportunities for you from EMC China,if it's fit for you .Plz touch me,thanks for your support!
Christina(028)86701200 QQ:1106525264Principal Software QA Engineer - USD/ChengduRe...
When using 28335, when the board is working normally and the AD conversion is not started, the signal is very good. However, once the signal is collected by AD, the signal is interfered. The signal vo...
[size=4] [md]## Preface In the previous article, we simulated speed data through light sensor data, and used online IDE to complete data collection and synchronous display. We experienced the quick de...
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
Abstract: In recent years, with the establishment and grid-connected power generation of a large number of solar photovoltaic power stations at home and abroad, photovoltaic grid-connected inverter...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
With the popularity of digital appliances, rechargeable batteries can be seen everywhere in people's daily lives and have become one of the indispensable daily necessities.
This article gives ...[Details]
At present,
the control system used in
automobiles
can be divided into three parts from the functional point of view:
sensor
unit, control unit and execution unit. Among them,
th...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
0 Introduction
PROFIBUS is an open digital communication system with a wide range of applications, which has been included in the international standards IEC 61158 and IEC 61784. Since the gen...[Details]
The number of timers/counters and interrupt sources directly determines the performance of the microcontroller. The MCS-51 microcontroller has two programmable 16-bit timers/counters and five inter...[Details]
The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
...[Details]
According to the National Shipbuilding Industry Economic Research Center, the total shipbuilding capacity in my country last year was about 9×106t. The new ship orders exceeded 17×106t, accounting ...[Details]
1. Introduction
Diesel engine test is the last key process in the diesel engine production process, which plays a very important role in the manufacturing quality of diesel engines. Its main c...[Details]
1 Introduction
In recent years, the application of LED display screens has developed rapidly, promoting the progress of LED driver ICs. Based on the high reliability of LEDs and the consistenc...[Details]
Linux and Android
京公网安备 11010802033920号
EEWORLD
