ZX100R datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Discrete semiconductor> diode> ZX100R

ZX100R: DescriptionZener Diode, 100V V(Z), 5%, 1.6W, Silicon, Unidirectional, DO-4, ROHS COMPLIANT, METAL PACKAGE-1; CategoryDiscrete semiconductor diode; File Size109KB，2 Pages; ManufacturerDIOTEC; Websitehttp://www.diotec.com/; Environmental Compliance

Download Datasheet Parametric View All

ZX100R Overview

Zener Diode, 100V V(Z), 5%, 1.6W, Silicon, Unidirectional, DO-4, ROHS COMPLIANT, METAL PACKAGE-1

ZX100R Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	DIOTEC
Parts packaging code	DO-4
package instruction	ROHS COMPLIANT, METAL PACKAGE-1
Contacts	1
Reach Compliance Code	compli
ECCN code	EAR99
Shell connection	ANODE
Configuration	SINGLE
Diode component materials	SILICON
Diode type	ZENER DIODE
Maximum dynamic impedance	150 Ω
JEDEC-95 code	DO-4
JESD-30 code	O-MUPM-D1
Humidity sensitivity level	1
Number of components	1
Number of terminals	1
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package body material	METAL
Package shape	ROUND
Package form	POST/STUD MOUNT
Peak Reflow Temperature (Celsius)	260
polarity	UNIDIRECTIONAL
Maximum power dissipation	1.6 W
Certification status	Not Qualified
Nominal reference voltage	100 V
surface mount	NO
technology	ZENER
Terminal form	SOLDER LUG
Terminal location	UPPER
Maximum time at peak reflow temperature	NOT SPECIFIED
Maximum voltage tolerance	5%
Working test current	5 mA

Preview

Download Datasheet

View All

ZX10 ... ZX200 (12.5 W)

Silicon-Power-Z-Diodes (non-planar technology)

Silizium-Leistungs-Z-Dioden (flächendiffundierte Dioden)

Version 2008-04-09

Maximum power dissipation

Maximale Verlustleistung

Nominal Z-voltage

Nominale Z-Spannung

Metal case

Metallgehäuse

Weight approx. – Gewicht ca.

Standard polarity: Cathode to stud / Kathode am Gewinde

Index R: Anode to stud / Anode am Gewinde (e. g. ZX10R)

Standard packaging: bulk

Standard Lieferform: lose im Karton

12.5 W

10 ... 200 V

DO-4

5.5 g

Ø2

SW11

Dimensions - Maße [mm]

Standard Zener voltage tolerance is graded to the international E 24 (~ ±5%) standard.

Other voltage tolerances and higher Zener voltages on request.

Die Toleranz der Zener-Spannung ist in der Standard-Ausführung gestuft nach der internationalen

Reihe E 24 (~ ±5%). Andere Toleranzen oder höhere Arbeitsspannungen auf Anfrage.

Maximum ratings

Power dissipation without cooling fin

Verlustleistung ohne Kühlblech

Power dissipation with cooling fin 150 cm

Verlustleistung mit Kühlblech 150 cm

Non repetitive peak power dissipation, t < 10 ms

Einmalige Impuls-Verlustleistung, t < 10 ms

Admissible mounting torque

Zulässiges Anzugsdrehmoment

Operating junction temperature – Sperrschichttemperatur

Storage temperature – Lagerungstemperatur

Thermal resistance junction to ambient air

Wärmewiderstand Sperrschicht – umgebende Luft

Thermal Resistance Junction – Case

Wärmewiderstand Sperrschicht – Gehäuse

thA

thC

= 25°C

tot

ZSM

Type

Grenzwerte

1.6 W

12.5 W

100 W

1 Nm

-55...+150°C

-55...+175°C

< 80 K/W

< 5 K/W

Zener voltages see table on next page – Zener-Spannungen siehe Tabelle auf der nächsten Seite

Valid if mounted on vertical cooling fin 150 cm² – Gültig bei Montage auf senkrecht stehendem Kühlblech 150 cm

http://www.diotec.com/

Recommended Resources

AMP-04 0 to 400℃ temperature measurement circuit

JK8 proximity switch circuit

Step Up/Step Down Current Source Battery Charger

collector amplitude modulation circuit

Dirty gas detection notification device

Industrial node controller PCB diagram, take a sneak peek!: Almost done, haha, the front-end signal conditioning part of the ADC is still missing. Take a look![[i] This post was last edited by chenzhufly on 2012-9-17 15:19[/i]]...; chenzhufly DSP and ARM Processors

After adding some drivers to the kernel, it can't start: After adding some drivers to the kernel, it can't start up. The following is the information output by the serial port: ERROR: StoreImageToBootMedia: Failed to write region to BINFS partition (start=0...; cqr059999 Embedded System

I hope the mobile version of the forum can be improved: I hope the mobile version of the forum can have a check-in function....; 凤凰息梧桐 Suggestions & Announcements

How to apply for ARM7 experimental board: I have learned ARM9. I have studied for half a year but still haven't gotten started. I want to learn ARM7 to do a project....; happyming0809 NXP MCU

EVC pop-up menu: I want to click a button to generate a pop-up menu. The code is as follows: CMenu menu; menu.LoadMenu(IDR_MENU1); CMenu *pPopup=menu.GetSubMenu(1); pPopup->TrackPopupMenu(TPM_LEFTALIGN,100,100,this); ...; hemp Embedded System

"Community Lecture" Logic Synthesis of High Design Reliability in DO-254 (VI) -- Engineering Considerations for DO-254: DO-254 projects require more considerations during synthesis. Logic synthesis tools can provide a lot of additional value in design reliability. The following are some of the most important features i...; 心仪 FPGA/CPLD

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components