EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN0502E1321DST

Description
Fixed Resistor, Thin Film, 0.1W, 1320ohm, 75V, 0.5% +/-Tol, -25,25ppm/Cel, 0602,
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

PTN0502E1321DST Overview

Fixed Resistor, Thin Film, 0.1W, 1320ohm, 75V, 0.5% +/-Tol, -25,25ppm/Cel, 0602,

PTN0502E1321DST Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerVishay
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
JESD-609 codee3
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.571 mm
Package length1.397 mm
Package formSMT
Package width0.635 mm
method of packingTR
Rated power dissipation(P)0.1 W
resistance1320 Ω
Resistor typeFIXED RESISTOR
seriesPTN
size code0602
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Tolerance0.5%
Operating Voltage75 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Moisture resistant
High purity alumina substrate
Non-standard values available
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Compliant to RoHS directive 2002/95/EC
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic E of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
Coating
Nickel
Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 30 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE (Ω)
20 to 35K
20 to 65K
20 to 130K
10 to 80K
10 to 301K
10 to 301K
50 to 600K
10 to 1M
10 to 1M
10 to 1.75M
10 to 2M
10 to 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 02-Nov-09
For technical questions, contact:
thin-film@vishay.com
www.vishay.com
55
Why is there a loud sound when I touch point O, but no sound when I connect point O to the audio?
Why is there a loud sound when the hand touches point O, and why is there no sound when the audio is connected to point O?...
boofeng2002 Analog electronics
Created an Atmel Cortex-x exchange group, group number: 325358586 Welcome everyone to join the exchange
Created an Atmel Cortex-x exchange group, group number: 325358586 Welcome everyone to join the exchange...
littleshrimp Microchip MCU
Ask for advice on USB development of stm32f107RB
I want to ask if stm32f107RB can use firmware library V2.0 and USB 2.0 library to develop USB devices. I have been looking at the firmware library of v3.0 USB-OTG-FS for a week. There are many conditi...
天马行风 stm32/stm8
Reversi production - LabVIEW design interface exploration
LabVIEW:) 8!8...
心仪 Test/Measurement
A novice is looking for the parameters of the PWM control output 0-10V circuit of the microcontroller
I want to make a circuit that uses a single-chip microcomputer to control pwm and output 0-10v to control equipment. As shown in the figure, the pwm signal drives Q2 after passing through Q1, and the ...
qqings Power technology
The Woods We Passed Through During Those Years (2)
[align=left][b][font=微软雅黑][size=3]The following content is purely arbitrary and fabricated. Any similarity is unfortunate! [/size][/font][/b][/align] [align=left][font=微软雅黑][size=3] It takes a thousan...
eric_wang Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1486  1385  1931  1481  1999  30  28  39  41  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号