EEWORLDEEWORLDEEWORLD

Part Number

Search

LTSHCRE-104-S-14-185-GT-LT-001

Description
Board Connector, 4 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size139KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

LTSHCRE-104-S-14-185-GT-LT-001 Overview

Board Connector, 4 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

LTSHCRE-104-S-14-185-GT-LT-001 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerMajor League Electronics
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresMATING PIN LENGTH=0.185 INCH
body width0.1 inch
subject depth0.26 inch
body length0.4 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
JESD-609 codee0
Manufacturer's serial numberLTSHCRE
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness10u inch
polarization keyPOLAR PIN POSITION
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.055 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts4
Share: Problems with using LM25119
[i=s] This post was last edited by qwqwqw2088 on 2018-9-21 15:51 [/i] [size=4][b]Question 1: LM25119 application problem [/b] As shown in the attached schematic diagram, I used LM25119 to make a power...
qwqwqw2088 Analogue and Mixed Signal
There is a problem
I applied to make a single-chip microcomputer experimental platform for college students that can conduct 51, avr, and arm experiments. I want to name it "single-chip microcomputer and embedded compre...
conniezhou Embedded System
I have a speic circuit problem. I can calculate and simulate it, but there is a problem when I make it. Please help me!!
According to the speic circuit model, L1=L2=100uH is calculated (using an I-shaped inductor). Cs is a 22uF polar capacitor, MOS tube is IRF540N, pwm is 20k, output capacitor is 104 and 10uF polar capa...
孤鹰 Integrated technical exchanges
EEWORLD DIY——Balancing Car
This is my first time to participate in a forum activity. I made a very mature balancing car. The MCU is STM32F103C8T6, the gyroscope is MPU6050, the motor driver is TB6612, the reduction motor and en...
gujiamao DIY/Open Source Hardware
Please advise on the position of the rectifier bridge and common-mode inductor in power supply design
The positions of the common mode inductor and filter are different in the following two figures. In the power supply design cases of some large manufacturers, the common mode filtering is done after r...
kal9623287 Power technology
Analysis and Measurement of Intrinsic Noise in Operational Amplifier Circuits
Analysis and measurement of inherent noise in operational amplifier circuits, good information:...
yemingxp Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 214  2843  2184  1989  2130  5  58  44  41  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号