reduces quiescent current to 25µA, ensuring high efficiency
across the entire load range. An internal soft-start limits
inrush current during start-up.
Other features include a <1µA shutdown current and robust
protection under short-circuit, thermal overload, and output
overvoltage conditions. The LTC3121 is offered in a low
profile 12-lead (3mm × 4mm × 0.75mm) DFN package.
n
n
n
n
n
V
IN
Range: 1.8V to 5.5V, 500mV After Start-Up
Output Voltage Range: 2.2V to 15V
400mA Output Current for V
IN
= 5V and V
OUT
= 12V
Output Disconnects from Input When Shut Down
Synchronous Rectification: Up to 95% Efficiency
Inrush Current Limit
Up to 3MHz Adjustable Switching Frequency
Synchronizable to External Clock
Selectable Burst Mode
®
Operation: 25µA I
Q
Output Overvoltage Protection
Soft-Start
<1µA I
Q
in Shutdown
12-Lead, 3mm × 4mm Thermally Enhanced DFN
Package
applicaTions
n
n
n
n
PCI Express Cards/Systems
Piezo Actuators
Small DC Motors
12V Analog Rail From Battery, 5V, or Backup Capacitor
L,
LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks
and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
Typical applicaTion
5V to 12V Synchronous Boost Converter with Output Disconnect
V
IN
5V
6.8µH
SW
V
IN
4.7µF
OFF ON
BURST PWM
SD
LTC3121
V
OUT
100nF
CAP
FB
V
C
SGND
4.7µF
PGND
210k
390pF
10pF
113k
1.02M
22µF
100
90
V
OUT
12V
400mA
80
EFFICIENCY (%)
70
60
50
40
30
20
10
0
0.01
0.1
10
1
LOAD CURRENT (mA)
100
0.01
600
PWM POWER LOSS
0.1
Burst Mode
OPERATION
PWM
1
POWER LOSS (W)
Efficiency Curve
10
PWM/SYNC
RT
V
CC
57.6k
3121 TA01b
3121 TA01a
3121fa
For more information
www.linear.com/LTC3121
1
LTC3121
absoluTe MaxiMuM raTings
(Note 1)
pin conFiguraTion
TOP VIEW
SW
PGND
V
IN
PWM/SYNC
V
CC
RT
1
2
3
4
5
6
13
PGND
12 CAP
11 V
OUT
10 SGND
9
8
7
SD
FB
V
C
V
IN
Voltage .................................................. –0.3V to 6V
V
OUT
Voltage ............................................ –0.3V to 18V
SW Voltage (Note 2) .................................. –0.3V to 18V
SW Voltage (Pulsed < 100ns) (Note 2)....... –0.3V to 19V
V
C
, RT Voltage .......................................... –0.3V to V
CC
CAP Voltage
V
OUT
< 5.7V ............................–0.3V to (V
OUT
+ 0.3V)
5.7V ≤ V
OUT
≤ 11.7V...... (V
OUT
– 6V) to (V
OUT
+ 0.3V)
V
OUT
> 11.7V .................................(V
OUT
– 6V) to 12V
All Other Pins ............................................... –0.3V to 6V
Operating Junction Temperature Range
(Notes 3, 4) ............................................ –40°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
DE PACKAGE
12-LEAD (4mm
×
3mm) PLASTIC DFN
T
JMAX
= 125°C,
θ
JA
= 43°C/W (NOTE 5),
θ
JC
= 5°C/W
EXPOSED PAD (PIN 13) IS PGND,
MUST BE SOLDERED TO PCB FOR RATED THERMAL PERFORMANCE
orDer inForMaTion
LEAD FREE FINISH
LTC3121EDE#PBF
LTC3121IDE#PBF
TAPE AND REEL
LTC3121EDE#TRPBF
LTC3121IDE#TRPBF
http://www.linear.com/product/LTC3121#orderinfo
PART MARKING*
3121
3121
PACKAGE DESCRIPTION
12-Lead (4mm × 3mm) Plastic DFN
12-Lead (4mm × 3mm) Plastic DFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
2
3121fa
For more information
www.linear.com/LTC3121
LTC3121
elecTrical characTerisTics
PARAMETER
Minimum Start-Up Voltage
Input Voltage Range
Output Voltage Adjust Range
Feedback Voltage
Feedback Input Current
Quiescent Current, Shutdown
Quiescent Current, Active
Quiescent Current, Burst
N-channel MOSFET Switch Leakage Current
P-channel MOSFET Switch Leakage Current
N-channel MOSFET Switch On-Resistance
P-channel MOSFET Switch On-Resistance
N-channel MOSFET Current Limit
Maximum Duty Cycle
Minimum Duty Cycle
Switching Frequency
SYNC Frequency Range
PWM/SYNC Input High
PWM/SYNC Input Low
PWM/SYNC Input Current
CAP Clamp Voltage
Error Amplifier Transconductance
Error Amplifier Output Current
Soft-Start Time
SD
Input High
SD
Input Low
SD
Input Current
V
SD
= 5.5V
l
l
The
l
denotes the specifications which apply over the full operating junction
temperature range, otherwise specifications are at T
A
= 25°C (Note 3). V
IN
= 3.6V, V
OUT
= 12V, RT = 57.6k unless otherwise noted.
CONDITIONS
V
OUT
= 0V
After V
OUT
≥ 2.2V
l
l
l
l
MIN.
0.5
2.2
1.178
TYP
1.7
MAX
1.8
5.5
15
UNITS
V
V
V
V
nA
µA
µA
µA
µA
µA
µA
Ω
Ω
1.202
1
0.01
500
25
10
1.225
50
1
700
40
20
30
70
V
FB
= 1.4V
V
SD
= 0V, V
OUT
= 0V, Not Including Switch Leakage
V
C
= 0V, Measured On V
IN
, Non-Switching
Measured on V
IN
, V
FB
> 1.4V
Measured on V
OUT
, V
FB
> 1.4V
V
SW
= 15V, V
OUT
= 15V, V
C
= 0V (Note 6)
V
SW
= V
IN
= 0V, V
OUT
= 15V (Note 6)
l
l
0.1
0.1
0.121
0.188
V
IN
= 3.3V
V
FB
= 1.0V
V
FB
= 1.4V
l
l
l
l
l
l
l
1.5
90
0.85
0.1
0.9 •V
CC
1.8
94
2.7
0
A
%
%
MHz
MHz
V
V
µA
V
µS
µA
ms
V
1
1.15
3
0.1•V
CC
V
PWM/SYNC
= 5.5V
V
OUT
> 6.1V, Referenced to V
OUT
l
0.01
–5.2
70
–5.6
100
±25
10
1.6
1
–6.0
130
0.25
1
2
V
µA
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Voltage transients on the SW pin beyond the DC limit specified in
the Absolute Maximum Ratings are non-disruptive to normal operations
when using good layout practices, as shown on the demo board or
described in the data sheet or application notes.
Note 3:
The LTC3121 is tested under pulsed load conditions such that
T
A
≈ T
J
. The LTC3121E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 125°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LTC3121I is guaranteed
to meet specifications over the full –40°C to 125°C operating junction
temperature range. The junction temperature (T
J
in °C) is calculated from
the ambient temperature (T
A
in °C) and power dissipation (P
D
in watts)
according to the formula: T
J
= T
A
+ (P
D
•
θ
JA
) where
θ
JA
is the thermal
impedance of the package.
Note 4:
The LTC3121 includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature shutdown is active.
Continuous operation above the specified maximum operating junction
temperature may result in device degradation or failure.
Note 5:
Failure to solder the exposed backside of the package to the PC
board ground plane will result in a thermal impedance much higher than
the rated package specifications.
Note 6:
Measured using a propietary test mode to ensure anti-ringing
switch between V
IN
ans SW is not active.
3121fa
For more information
www.linear.com/LTC3121
3
LTC3121
Configured as front page application unless otherwise specified.
When I write code now, I always copy the entire project file for backup. I used git before but I haven't used it for a long time. Can you share which tool you use and which one is easy to use?...
Electronics manufacturers need to integrate and connect the entire product development, manufacturing and product lifecycle processes from the beginning, but to achieve this, PDM systems alone are not...
I am currently working in a small ODM company. The company is not large and I have to do all kinds of work. I can learn a lot, but there are many limitations. There are not many resources to access. W...
Event details: [Boliu BL606P audio and video development board]Updated to 2023-03-08Evaluation report summary:@swzswz[Boliu BL606P audio and video development board] + driving LED digital tube[Boliu B...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
RS-422 and RS-485 are both serial data interface standards, which were developed and published by the Electronic Industries Association (EIA). RS-422 defines a balanced communication interface with a ...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
