reduces quiescent current to 25µA, ensuring high efficiency
across the entire load range. An internal soft-start limits
inrush current during start-up.
Other features include a <1µA shutdown current and robust
protection under short-circuit, thermal overload, and output
overvoltage conditions. The LTC3121 is offered in a low
profile 12-lead (3mm × 4mm × 0.75mm) DFN package.
n
n
n
n
n
V
IN
Range: 1.8V to 5.5V, 500mV After Start-Up
Output Voltage Range: 2.2V to 15V
400mA Output Current for V
IN
= 5V and V
OUT
= 12V
Output Disconnects from Input When Shut Down
Synchronous Rectification: Up to 95% Efficiency
Inrush Current Limit
Up to 3MHz Adjustable Switching Frequency
Synchronizable to External Clock
Selectable Burst Mode
®
Operation: 25µA I
Q
Output Overvoltage Protection
Soft-Start
<1µA I
Q
in Shutdown
12-Lead, 3mm × 4mm Thermally Enhanced DFN
Package
applicaTions
n
n
n
n
PCI Express Cards/Systems
Piezo Actuators
Small DC Motors
12V Analog Rail From Battery, 5V, or Backup Capacitor
L,
LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks
and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
Typical applicaTion
5V to 12V Synchronous Boost Converter with Output Disconnect
V
IN
5V
6.8µH
SW
V
IN
4.7µF
OFF ON
BURST PWM
SD
LTC3121
V
OUT
100nF
CAP
FB
V
C
SGND
4.7µF
PGND
210k
390pF
10pF
113k
1.02M
22µF
100
90
V
OUT
12V
400mA
80
EFFICIENCY (%)
70
60
50
40
30
20
10
0
0.01
0.1
10
1
LOAD CURRENT (mA)
100
0.01
600
PWM POWER LOSS
0.1
Burst Mode
OPERATION
PWM
1
POWER LOSS (W)
Efficiency Curve
10
PWM/SYNC
RT
V
CC
57.6k
3121 TA01b
3121 TA01a
3121fa
For more information
www.linear.com/LTC3121
1
LTC3121
absoluTe MaxiMuM raTings
(Note 1)
pin conFiguraTion
TOP VIEW
SW
PGND
V
IN
PWM/SYNC
V
CC
RT
1
2
3
4
5
6
13
PGND
12 CAP
11 V
OUT
10 SGND
9
8
7
SD
FB
V
C
V
IN
Voltage .................................................. –0.3V to 6V
V
OUT
Voltage ............................................ –0.3V to 18V
SW Voltage (Note 2) .................................. –0.3V to 18V
SW Voltage (Pulsed < 100ns) (Note 2)....... –0.3V to 19V
V
C
, RT Voltage .......................................... –0.3V to V
CC
CAP Voltage
V
OUT
< 5.7V ............................–0.3V to (V
OUT
+ 0.3V)
5.7V ≤ V
OUT
≤ 11.7V...... (V
OUT
– 6V) to (V
OUT
+ 0.3V)
V
OUT
> 11.7V .................................(V
OUT
– 6V) to 12V
All Other Pins ............................................... –0.3V to 6V
Operating Junction Temperature Range
(Notes 3, 4) ............................................ –40°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
DE PACKAGE
12-LEAD (4mm
×
3mm) PLASTIC DFN
T
JMAX
= 125°C,
θ
JA
= 43°C/W (NOTE 5),
θ
JC
= 5°C/W
EXPOSED PAD (PIN 13) IS PGND,
MUST BE SOLDERED TO PCB FOR RATED THERMAL PERFORMANCE
orDer inForMaTion
LEAD FREE FINISH
LTC3121EDE#PBF
LTC3121IDE#PBF
TAPE AND REEL
LTC3121EDE#TRPBF
LTC3121IDE#TRPBF
http://www.linear.com/product/LTC3121#orderinfo
PART MARKING*
3121
3121
PACKAGE DESCRIPTION
12-Lead (4mm × 3mm) Plastic DFN
12-Lead (4mm × 3mm) Plastic DFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
2
3121fa
For more information
www.linear.com/LTC3121
LTC3121
elecTrical characTerisTics
PARAMETER
Minimum Start-Up Voltage
Input Voltage Range
Output Voltage Adjust Range
Feedback Voltage
Feedback Input Current
Quiescent Current, Shutdown
Quiescent Current, Active
Quiescent Current, Burst
N-channel MOSFET Switch Leakage Current
P-channel MOSFET Switch Leakage Current
N-channel MOSFET Switch On-Resistance
P-channel MOSFET Switch On-Resistance
N-channel MOSFET Current Limit
Maximum Duty Cycle
Minimum Duty Cycle
Switching Frequency
SYNC Frequency Range
PWM/SYNC Input High
PWM/SYNC Input Low
PWM/SYNC Input Current
CAP Clamp Voltage
Error Amplifier Transconductance
Error Amplifier Output Current
Soft-Start Time
SD
Input High
SD
Input Low
SD
Input Current
V
SD
= 5.5V
l
l
The
l
denotes the specifications which apply over the full operating junction
temperature range, otherwise specifications are at T
A
= 25°C (Note 3). V
IN
= 3.6V, V
OUT
= 12V, RT = 57.6k unless otherwise noted.
CONDITIONS
V
OUT
= 0V
After V
OUT
≥ 2.2V
l
l
l
l
MIN.
0.5
2.2
1.178
TYP
1.7
MAX
1.8
5.5
15
UNITS
V
V
V
V
nA
µA
µA
µA
µA
µA
µA
Ω
Ω
1.202
1
0.01
500
25
10
1.225
50
1
700
40
20
30
70
V
FB
= 1.4V
V
SD
= 0V, V
OUT
= 0V, Not Including Switch Leakage
V
C
= 0V, Measured On V
IN
, Non-Switching
Measured on V
IN
, V
FB
> 1.4V
Measured on V
OUT
, V
FB
> 1.4V
V
SW
= 15V, V
OUT
= 15V, V
C
= 0V (Note 6)
V
SW
= V
IN
= 0V, V
OUT
= 15V (Note 6)
l
l
0.1
0.1
0.121
0.188
V
IN
= 3.3V
V
FB
= 1.0V
V
FB
= 1.4V
l
l
l
l
l
l
l
1.5
90
0.85
0.1
0.9 •V
CC
1.8
94
2.7
0
A
%
%
MHz
MHz
V
V
µA
V
µS
µA
ms
V
1
1.15
3
0.1•V
CC
V
PWM/SYNC
= 5.5V
V
OUT
> 6.1V, Referenced to V
OUT
l
0.01
–5.2
70
–5.6
100
±25
10
1.6
1
–6.0
130
0.25
1
2
V
µA
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Voltage transients on the SW pin beyond the DC limit specified in
the Absolute Maximum Ratings are non-disruptive to normal operations
when using good layout practices, as shown on the demo board or
described in the data sheet or application notes.
Note 3:
The LTC3121 is tested under pulsed load conditions such that
T
A
≈ T
J
. The LTC3121E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 125°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LTC3121I is guaranteed
to meet specifications over the full –40°C to 125°C operating junction
temperature range. The junction temperature (T
J
in °C) is calculated from
the ambient temperature (T
A
in °C) and power dissipation (P
D
in watts)
according to the formula: T
J
= T
A
+ (P
D
•
θ
JA
) where
θ
JA
is the thermal
impedance of the package.
Note 4:
The LTC3121 includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature shutdown is active.
Continuous operation above the specified maximum operating junction
temperature may result in device degradation or failure.
Note 5:
Failure to solder the exposed backside of the package to the PC
board ground plane will result in a thermal impedance much higher than
the rated package specifications.
Note 6:
Measured using a propietary test mode to ensure anti-ringing
switch between V
IN
ans SW is not active.
3121fa
For more information
www.linear.com/LTC3121
3
LTC3121
Configured as front page application unless otherwise specified.
[size=4] I am currently working on the development of DM368 USB. I am new to USB driver development and am not very familiar with it. My classmates recommended this series of books to me. Now I want t...
In this article, we will explore:
What is Ultra Wideband?
What is it used for?
How is ultra-wideband technology used in mobile phones?
What this means to you.
What is UWB and why should you care?Googl...
[Nucleo Experience] +USART communication problem between ST-LINK and L053 was discovered through the reminder of netizens: ST-LINK's virtual serial port has been connected to the target M0+ USART's tr...
The read identification word is 3E:3E:3E. The program written is displayed normally, but the program read out is allusing Zhifeng programmer, high voltage programming mode[[i] This post was last edite...
Error:Target DLL has been cancelled.Debugger aborted! I am a beginner in microcontrollers and I really want to learn it well! I am doing the first example in the "Proteus Chinese Tutorial", which seem...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
Linux and Android
京公网安备 11010802033920号
EEWORLD
