a. Device mounted with all leads soldered or welded to PC board.
b. Derate 8.3 mW/_C above T
A
= 25_C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Typical values for dropout voltage at V
OUT
w
2 V are measured at
V
OUT
= 3.3 V, while typical values for dropout voltage at V
OUT
< 2 V are measured at V
OUT
= 1.8 V.
d. Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the output voltage measured with a 1-V
differential, provided that V
IN
does not not drop below 2.0 V.
e. The device’s shutdown pin includes a typical 6-MW internal pull-down resistor connected to ground.
f.
V
OUT
is defined as the output voltage of the DUT at 1 mA.
g. The Error Output (Low) function is guaranteed from V
OUT
= 2.0 V to V
OUT
= 5.0 V.
h. The Power_Good trip threshold function is guaranteed from V
OUT
= 1.5 V to V
OUT
= 5.0 V and V
IN
w
2.0 V.
Document Number: 71119
S-50955—Rev. F, 16-May-05
www.vishay.com
3
Si9181
Vishay Siliconix
TIMING WAVEFORMS
V
IN
t
ON
V
NOM
0.95 V
NOM
V
OUT
ERROR
t
DELAY
FIGURE 4.
Timing Diagram for Power-Up
PIN CONFIGURATION
TSSOP-8
C
NOISE
DELAY
GND
V
IN
1
2
3
4
Top View
8
7
6
5
SD
ERROR
SENSE or ADJ
V
OUT
PIN DESCRIPTION
Pin Number
1
2
3
4
5
6
7
8
www.vishay.com
Name
C
NOISE
DELAY
GND
V
IN
V
OUT
SENSE or ADJ
ERROR
SD
Function
Noise bypass pin. For low noise applications, a 0.01-mF or larger ceramic capacitor should be connected from this pin
to ground.
Capacitor connected from this pin to ground will allow a delayed power-on-reset signal at the ERROR (Pin 7) output.
Refer to Figure 4.
Ground pin. Local ground for C
NOISE
and C
OUT
.
Input supply pin. Bypass this pin with a 2.2-mF ceramic or tantalum capacitor to ground.
Output voltage. Connect C
OUT
between this pin and ground.
For fixed output voltage versions, this pin should be connected to V
OUT
(Pin 5). For adjustable output voltage version,
this voltage feedback pin sets the output voltage via an external resistor divider.
This open drain output is an error flag output which goes low when V
OUT
drops 5% below its nominal voltage. This pin
also provides a power-on-reset signal if a capacitor is connected to the DELAY pin.
By applying less than 0.4 V to this pin, the device will be turned off. Connect this pin to V
As the title says, I recently made something that needed to use division operations, but when I tried to compile it in the simulate debugging mode under the IAR compilation environment, I found that, ...
I want to use the differential input terminal of ADC0804 to measure voltage. VIN+ inputs positive voltage and VIN- inputs negative voltage. My understanding is that the measured voltage at the output ...
I made a cv soc board, connected to a DDR3, a QSPI flash on the hps side, an SD card, set up an HPS in the qsys of the quartus project (with QSPI, SD/MMC, three interconnection buses), a jtag-uart, a ...
[size=4]1. Currently, almost all UPS used in my country's telecommunications systems are ([hide]online UPS[/hide])[/size][size=4] [/size] [size=4]2. If the technical performance is ranked, the correct...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
