EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTCRSM-112-S-16-H-200-001-S

Description
Board Connector, 12 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Receptacle
CategoryThe connector    The connector   
File Size238KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTCRSM-112-S-16-H-200-001-S Overview

Board Connector, 12 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Receptacle

BSTCRSM-112-S-16-H-200-001-S Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresMATING PIN=0.185\",HIGH TEMP
body length1.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial numberBSTCRSM
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Number of connectorsONE
PCB row number2
Number of rows loaded1
Maximum operating temperature250 °C
Minimum operating temperature-65 °C
PCB contact patternSTAGGERED
PCB contact row spacing3.175 mm
Plating thickness30u inch
polarization keyPOLAR PIN POSITION
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch5.08 mm
Total number of contacts12
How to make a serial port interrupt receiving program to receive one frame of data at a time
I would like to ask you if it is possible to make a receiving program for serial port interrupt, which receives a string of data each time it enters interruption and ends when it encounters a specifie...
stycx stm32/stm8
About temperature control
I want to make a device that can measure temperature at multiple points. What should I do?...
xkwirelessgroup Embedded System
LM324+IRF540N voltage follower problem
As shown in the simulation diagram, LM324 and IRF540N form a voltage follower. Below 10V, the output is the input voltage, but above 10V, the output can only reach 10V. I don't quite understand the pr...
番茄wo唯一 Power technology
Studying the Xunwei 4412 development board, questions about the LED light test routine
[color=#333333][font="][size=14px]I have been learning Xunwei's 4412 development board for a while. Today I encountered a problem [/size][/font][/color][color=#333333][font="][size=14px]I used Xunwei'...
马佳徐徐 Embedded System
Please share the book "RF Power Amplifier Circuit Design"
[i=s] This post was last edited by paulhyde on 2014-9-15 03:01 [/i] Please share the book "RF Power Amplifier Circuit Design", written by Huang Zhiwei...
zm12 Electronics Design Contest
The output signal of the inverse proportional op amp is wrong
[i=s]This post was last edited by xiaxingxing on 2021-9-22 13:42[/i]As shown in Figure 1, the circuit with an amplification factor of -1 composed of the operational amplifier LT1797CS5 has the followi...
xiaxingxing Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1245  649  2187  36  849  26  14  45  1  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号