EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GG-03-3011-BD

Description
Array/Network Resistor, Divider, Thin Film, 0.25W, 3010ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0303, CHIP
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GG-03-3011-BD Overview

Array/Network Resistor, Divider, Thin Film, 0.25W, 3010ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0303, CHIP

WBA-T0303GG-03-3011-BD Parametric

Parameter NameAttribute value
package instructionSMT, 0303
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
The first element resistor1505 Ω
Manufacturer's serial numberWBA
Installation featuresSURFACE MOUNT
Network TypeDIVIDER
Number of components2
Number of functions1
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width0.762 mm
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance3010 Ω
Resistor typeARRAY/NETWORK RESISTOR
Second/last element resistor1505 Ω
seriesWBA
size code0303
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Temperature coefficient tracking2 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
[MM32 eMiniBoard Review] + OLED screen driver display
[i=s]This post was last edited by jinglixixi on 2020-11-1 00:14[/i]1. Use GPIO port to simulate I2C interface An LED flashing program is provided in the example. Through it, we can master the method o...
jinglixixi Domestic Chip Exchange
I want to ask if there is a wince development company in Zhengzhou?
I want to ask if there is a wince development company in Zhengzhou?...
lychome198 Embedded System
What is a push-pull power amplifier?
Using two transistors with the same characteristics, make them both work in Class B state, one of which works in the positive half cycle and the other in the negative half cycle, and then try to combi...
Jacktang Analogue and Mixed Signal
How to speed up pmos shutdown and control the delay time within us
Recently, Pmos is used as a ms-level switch circuit. IRF5305s is selected, and the circuit schematic is shown in Figure 1. The signal is the MCU signal 3.3v, and the power supply is 12v. The MCU contr...
程秋香 Analogue and Mixed Signal
How to read and display the decimal part of DHT11 in the serial port
I would like to ask all the experts, how can DHT11 read and display the decimal part of temperature and humidity, how to write the program, please give me some advice! !...
夜雨星空 RF/Wirelessly
PCB Microchip Resin Selection Criteria
1. Low peak temperature If the peak temperature is too high, it will cause copper oxidation and affect the observation effect of the slice under the microscope. The powder and liquid will generate hea...
方学放 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2112  270  1367  115  389  43  6  28  3  8 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号