3072-706-3106 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 3072-706-3106

3072-706-3106: DescriptionBoard Connector, 6 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size153KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

3072-706-3106 Overview

Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

3072-706-3106 Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	POLARIZED
Board mount options	PCB EDGE LOCKING HOOK
subject depth	0.45 inch
body length	0.93 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact completed and terminated	GOLD OVER NICKEL
Contact point gender	FEMALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
DIN compliance	NO
Dielectric withstand voltage	1500VAC V
Filter function	NO
IEC compliance	NO
maximum insertion force	LIF N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	GLASS FILLED POLYESTER
JESD-609 code	e4
MIL compliance	NO
Plug contact pitch	0.156 inch
Plug information	MULTIPLE MATING PARTS AVAILABLE
Mixed contacts	NO
Installation method	STRAIGHT
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
Options	GENERAL PURPOSE
PCB contact pattern	RECTANGULAR
Plating thickness	15u inch
polarization key	POLARIZED KEY
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.125 inch
Terminal pitch	3.96 mm
Termination type	SOLDER
Total number of contacts	6
UL Flammability Code	94V-0
Evacuation force-minimum value	LIF N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Vertical Mount Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

HOLE

LEG

LOCKING

RAMP

POLARIZING KEY &

LOCKING RAMP

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

LM386 wired intercom circuit diagram

Programmable amplifier with gain from 10 to 90dB selectable in 10dB increments

Ventilation equipment automatic control circuit

Charger circuit that can restore the vitality of over-discharged batteries

Push-pull DC and DC converter circuit diagram using SG3525A

Zero-crossing comparison detection circuit diagram

Small things I made when I was studying 51 (I) -- Electronic timer: I made a lot of things when I was learning 51, but many of them did not leave complete data. Here I post one of the things I made with complete data, and I will post the things I have sorted out later...; kandy2059 51mcu

Why is there no lm3s9b96 in the stellarisWare dirvers folder?: I just downloaded StellarisWare from TI's official website, but why is there no lm3s9b96 in the dirvers folder?...; dreambutterfly Microcontroller MCU

How to configure TIM1_CH1 for output comparison: How to configure TIM1_CH1 for output comparison? Why does the example program modified directly by OCToggle in V3.2.0 not work,but the one modified by TIM2_CH1 works?...; GGRR stm32/stm8

Analysis of causes of electrical fast transient (EFT) failure and sharing of rectification experience: [size=4][b]1. Reasons for failure[/b] The electrical fast pulse test is of typical significance for testing the immunity of equipment. Since the rising edge of the electrical fast pulse test waveform ...; 木犯001号 Power technology

[ST Motor Evaluation] Task Initialization - Environment Construction: [b][color=#5E7384]This content is originally created by EEWORLD forum user [size=3]stp111[/size]. If you need to reprint or use it for commercial purposes, you must obtain the author's consent and ind...; stp111 stm32/stm8

The problem of the pin spacing of the BGA packaged DSP chip (the spacing is slightly different from that on the datasheet, I don’t know if there will be any problems during soldering): Hello everyone, I would like to ask you a question: When drawing the BGA package of a DSP chip (Blackfin 533) in the PCB, the size of the pins may be a little wrong. The spacing between the pins shoul...; ahzhong2001 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components