Development of wireless network module for audio and video digital conversion based on ARMProject budget:￥5,000~10,000
Development cycle: 30 days
Project Category: Embedded
Bidding requirements:Projec...
In the zstack protocol stack, I know that I can modify the channel and network PANID by modifying -DDEFAULT_CHANLIST and -DZDAPP_CONFIG_PAN_ID in f8wConfig.cfg before burning the program. However, I w...
Some students may ask, why not write about simultaneous opening? (Simultaneous opening means that both ends are servers, and both ends simultaneously establish connection requests to each other). On t...
#includeunsigned int pwm_start,pwm_end,pwm_wide=0; float fre=0.000; #define uchar unsigned char #define uint unsigned int #define lint long int unsigned int start,end; float data,num,m1; long int m2=1...
Intelligent connected cars from inside to outside: Current status and development of Internet of Vehicles : https://training.eeworld.com.cn/course/6135...
All relevant units:
In accordance with the relevant requirements of the provincial and municipal electric vehicle charging infrastructure construction work, in order to further standardize the...[Details]
After studying the F4 FSMC method to drive the touch screen for a few days, I have gained some understanding, which are listed below. The unorganized record is only for my own reference in the future...[Details]
This paper proposes a design scheme for an embedded CNC system based on ARM and FPGA. The software and hardware design of the ARM system, the implementation method of hardware fine interpolation ...[Details]
The storage media corresponding to the three boot modes of STM32 are built-in to the chip, they are: 1. User Flash = Flash built into the chip 2.SRAM = RAM area built into the chip, which is the m...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
Today I am using the AD function of the stm8s microcontroller. There are ten channels from AN0 to AN9 on the microcontroller. I want to use only three of them, AN5 to AN7. //ADC initialization void A...[Details]
When the program starts running, light A turns on for 5 seconds, then turns off, light B turns on for 5 seconds, light B turns off, light C turns on for 5 seconds, light C turns off, the program ends...[Details]
;The hardware connection circuit of the 51 single-chip microcomputer is as follows: ;P1.3 and P1.4 are each connected to a button; ;P0.0 and P0.3 are each connected to a light-emitting diode; ;P2.0~P...[Details]
Circuit: Using AT89S52 single chip microcomputer. P3.0 to P3.3 are connected to four external buttons. P3.4 to P3.7 are the bit selection ports for controlling the four digital tubes, and P1 is the s...[Details]
1. SCL is always controlled by the Master. SDA is controlled by the Slave when reading data and by the Master when writing data according to the direction of data transmission. After the 8-bit data i...[Details]
The data provided by the International Federation of Robotics (IFR World Robotics) well demonstrates the growth momentum of industrial robots around the world. Let's follow the industrial control e...[Details]
International Solar Photovoltaic Network News: On November 21, Australia's SMA Solar Technology Co., Ltd. signed a contract with the local government to provide photovoltaic inverters with an insta...[Details]
:For medium and large-scale domestic photovoltaic power stations, inverters generally go through an open bidding process. Due to the high technical content of power station design, it is necessary ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
