EEWORLDEEWORLDEEWORLD

Part Number

Search

8125SH9W1BI

Description
PUSHBUTTON SWITCH,STRAIGHT,SPDT,ON-(ON),WP STRAIGHT TERMINAL,3
CategoryMechanical and electronic products    switch   
File Size1017KB,16 Pages
ManufacturerC&K Components
Download Datasheet Parametric View All

8125SH9W1BI Overview

PUSHBUTTON SWITCH,STRAIGHT,SPDT,ON-(ON),WP STRAIGHT TERMINAL,3

8125SH9W1BI Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator angle
Actuator length0.218 inch
Actuator materialGLASS FILLED NYLON
Actuator typePUSHBUTTON
body width6.858 mm
body height46.7868 mm
Body length or diameter12.7 mm
Casing diameter0.25 inch
Nozzle length0.25 inch
Casing typeUNTHREADED
Center contact platingGOLD OVER NICKEL
Contact (DC) maximum rated power R load0.4VA@20VDC
Contact functionON-(ON)
Contact resistance0.05 mΩ
Dielectric withstand voltage1000VAC V
Electrical life60000 Cycle(s)
End contact materialCOPPER ALLOY
End contact platingGOLD OVER NICKEL
Shell materialSTAINLESS STEEL
Insulation resistance1000000000 Ω
insulator materialGLASS FILLED NYLON
Manufacturer's serial number8020
Installation featuresTHROUGH HOLE-STRAIGHT
Maximum operating temperature75 °C
Minimum operating temperature-30 °C
PCB hole count3
sealEPOXY
SolderabilityMIL-STD
surface mountNO
Switch actionVERTICAL
switch functionSPDT
Switch typePUSHBUTTON SWITCH
Terminal length0.964 inch
Terminal materialCOPPER ALLOY
Termination typeWIRE WRAP
WashabilityPARTIAL
Printed from www.freetradezone.com, a service of Partminer, Inc.
This Material Copyrighted By Its Respective Manufacturer
Amplifier main technical parameters description
Amplifier main technical parameters description...
JasonYoo Analog electronics
The problem that the USB in DE2-70 can only transmit 8-bit data
I wrote a small software to send data on my PC. The purpose is to send a string of characters through the USB port. The function is writeport(). It is transmitted to the DE2-70 experimental board thro...
coolgreen1 FPGA/CPLD
The process of WEBENCH design +2.8V-4.2V step-down output 2.5V0.8A circuit
[i=s] This post was last edited by qwqwqw2088 on 2014-8-14 23:07 [/i] 1. Design topic: 2.8V-4.2V step-down output 2.5V0.8A circuit 2. Design process Enter the design page and enter the circuit paramet...
qwqwqw2088 Analogue and Mixed Signal
Friends who want to join TI, please look here, here are the real test questions of Texas Instruments!
It mainly includes the following types: The fill-in-the-blank questions are relatively basic, most of which are single-chip microcomputers. I remember there are interrupt-filling questions, and there ...
alan000345 TI Technology Forum
2.6.27.10 Experience of using matlab2008b under Linux kernel
1. There are all kinds of tutorials on how to install it online, but it's not that troublesome. Just mount the iso and run the install.sh script (what if you can't mount the cdrom? Just create a cdrom...
paradoxfx Linux and Android
Zigbee Road Capable Discussion
I looked at the routing of Zigbee and found that there is a word in it that is very confusing, "Route Capability". The book says that if a device can establish a route to a destination device with the...
huyf RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2656  2844  2243  1315  1904  54  58  46  27  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号