Pad Layouts Solder Reflow and Rework Recommendations
The dimension in the table below provide the recommended pad layout for each 0805 device.
Pad Dimensions
Device
All 0805 Series
A
Nominal
1.20
B
Nominal
1.00
C
Nominal
1.50
Dimensions : Millimetres
Profile Feature
Average Ramp-Up Rate (T
s
maximum to T
p
)
Preheat:
Temperature Minimum (T
s
minimum)
Temperature Maximum (T
s
maximum)
Time (t
s
minimum to t
s
maximum)
Time maintained above:
Temperature (T
L
)
Time (t
L
)
Peak/Classification Temperature (T
p
):
Time within 5°C of actual Peak:
Temperature (t
p
)
Ramp-Down Rate:
Time 25°C to Peak Temperature:
Pb-Free Assembly
3°C/second maximum
150°C
200°C
60-180 seconds
217°C
60-150 seconds
260°C
20-40 seconds
6°C/second maximum
8 minutes maximum
Note 1: All temperatures refer to of the package, measured on the package body surface.
Solder reflow
Due to “Lead Free” nature, Temperature and Dwelling time for the soldering zone is higher than those for Regular. This may cause
damage to other components.
1. Recommended max past thickness > 0.25mm.
2. Devices can be cleaned using standard methods and aqueous solvent.
3. Rework use standard industry practices.
4. Storage Environment : < 30°C/60% RH.
Caution:
1. If reflow temperatures exceed the recommended profile, devices may not meet the performance requirements.
2. Devices are not designed to be wave soldered to the bottom side of the board.
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
Page <3>
17/05/11 V1.1
Surface Mountable PTC
Resettable Fuse
Reflow Profile
Temperature
Time
Part Number Table
Description
Surface Mountable PTC Resettable Fuse
Surface Mountable PTC Resettable Fuse
Surface Mountable PTC Resettable Fuse
Surface Mountable PTC Resettable Fuse
Surface Mountable PTC Resettable Fuse
Part Number
MC36206
MC36210
MC36213
MC36215
MC36220
Disclaimer
This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes
in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied.
The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data
sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage
resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded.
[i=s]This post was last edited by dontium on 2015-1-23 13:31[/i] It seems that everyone is working on ARM, embedded systems, and the Internet of Things. If a company wants to find an analog applicatio...
[i=s]This post was last edited by yuluozhishang on 2016-5-29 13:01[/i] [backcolor=rgb(239, 245, 249)]I am working on a magnetic field detection system for nails based on the 430F149 microcontroller an...
I looked at the Linux approach, it's quite complicated, designed into several layers: VFS, NTFS, FAT, IO, DRIVER, my God... Do I have to write all these codes myself?...
This is a function in the process of USB enumeration establishment. I don't understand this function very well. Please give me some advice~~~[/b][/color] uint8_t Setup0_Process(void) { union { uint8_t...
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
Distributed Wireless Communication System (DWCS) uses distributed antennas, distributed processing control, joint signal processing and other technologies to improve the system's spectrum efficie...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
For battery-powered portable devices, in addition to breaking through the limitations of processing power, the performance of portable system power supplies also needs to be continuously improved. ...[Details]
introduction
Temperature and humidity are the main environmental parameters of industrial and agricultural production. It is of great significance to measure them accurately and timely. Using a s...[Details]
Fairchild's FAN6208 is a synchronous rectification (SR) controller for isolated LLC or LC resonant converters that can drive two individual SR MOSFETs emulating the behavior of rectifier diodes. FAN62...[Details]
I. Introduction
The use of electronics in cars dates back to the early 20th century when electric starters replaced hand cranks. Automotive electronics became popular in the 1960s with the...[Details]
(1) Open circuit voltage of the battery
(2) Internal resistance of the battery
(3) Battery operating voltage
(4) Charging voltage
Charging voltage refers to the voltage applied ...[Details]
Previously used primarily in high-power power supplies and large industrial and consumer power supplies, supercapacitors are now finding their way into products of all sizes, especially portable de...[Details]
First, the choice of charging location. Wireless charging technology is related to the distance and state of the charger and the charged device. That is to say, the distance between the two cannot...[Details]
PID is proportional differential adjustment. You can refer to the detailed introduction in the automatic control course for details! The positive action and the negative action in temperature contr...[Details]
0 Introduction
In microwave, radar, radio and television, and communication systems, the problem of coupling RF power is often encountered. A directional coupler is a directional power divide...[Details]
The situation of "excessive neutral current" mentioned here means that when the three-phase load is balanced, the neutral current is still too large, and the neutral current is more than 1.5 times ...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
