5962-9458506HBA datasheet, PDF

Datasheet> All Categories > storage> storage> 5962-9458506HBA

5962-9458506HBA: DescriptionEEPROM Module, 128KX32, 120ns, Parallel, CMOS, CQFP68, CERAMIC, QFP-68; Categorystorage storage; File Size741KB，43 Pages; ManufacturerMicrosemi; Websitehttps://www.microsemi.com

Download Datasheet Parametric View All

5962-9458506HBA Overview

EEPROM Module, 128KX32, 120ns, Parallel, CMOS, CQFP68, CERAMIC, QFP-68

5962-9458506HBA Parametric

Parameter Name	Attribute value
Objectid	2078437784
package instruction	CERAMIC, QFP-68
Reach Compliance Code	unknown
Maximum access time	120 ns
Other features	USER CONFIGURABLE AS 512K X 8
Spare memory width	16
Data polling	YES
JESD-30 code	S-CQFP-G68
JESD-609 code	e0
length	23.875 mm
memory density	4194304 bit
Memory IC Type	EEPROM MODULE
memory width	32
Number of functions	1
Number of terminals	68
word count	131072 words
character code	128000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
organize	128KX32
Package body material	CERAMIC, METAL-SEALED COFIRED
encapsulated code	QFP
Encapsulate equivalent code	QFP68,.99SQ,50
Package shape	SQUARE
Package form	FLATPACK
page size	128 words
Parallel/Serial	PARALLEL
power supply	5 V
Programming voltage	5 V
Certification status	Not Qualified
Filter level	MIL-STD-883
Maximum seat height	4.06 mm
Maximum standby current	0.005 A
Maximum slew rate	0.25 mA
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	4.5 V
Nominal supply voltage (Vsup)	5 V
surface mount	YES
technology	CMOS
Temperature level	MILITARY
Terminal surface	TIN LEAD
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	QUAD
switch bit	NO
width	23.875 mm
Maximum write cycle time (tWC)	10 ms
write protect	SOFTWARE

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Added device type 06 for vendor cages 54230 and 88379. Added

vendor cage 0EU86 for device types 01 through 06. Figure 1,

changed case outline M to reflect package is available in either a

single or dual cavity. -sld

Added case outline 9.

Added device types 07, 08, and 09 for vendor cage 0EU86. Made

changes to table I to include the addition of device types 07, 08, and

09. Added a min limit to the table I for the I

, and the I

tests. Made

changes to Figures 2, 3, 4, 5, 6, and 8. -sld

Added case outline Z. Updated paragraph 1.2.4, 1.3, figures 1, 2,

and 8. -sld

Added case outline B. Added note to paragraph 1.2.4. -sld

Updated drawing paragraphs. -sld

Paragraph 1.2.4 Case outline M: Correct case outline M package

style from “single/dual” to “dual”. Paragraph 1.2.4 footnote 1/: Delete

“(single cavity)” and “Case outline A can be used if longer leads are

necessary”. Figure 1 case outline M: Correct figure 1 to reflect dual

cavity quad flatpack only for case outline M. -gc

DATE (YR-MO-DA)

99-05-14

APPROVED

K. A. Cottongim

00-04-06

02-01-31

Raymond Monnin

02-06-04

03-10-06

12-04-16

12-08-16

Raymond Monnin

Charles F. Saffle

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

Gary Zahn

CHECKED BY

Michael C. Jones

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS

AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

AMSC N/A

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

http://www.landandmaritime.dla.mil/

APPROVED BY

Kendall A. Cottongim

MICROCIRCUIT, HYBRID, MEMORY,

DIGITAL, 128K x 32-BIT, ELECTRICALLY

ERASABLE/PROGRAMMABLE READ ONLY

MEMORY

DRAWING APPROVAL DATE

94-08-02

REVISION LEVEL

SIZE

SHEET

CAGE CODE

67268

1 OF

5962-94585

DSCC FORM 2233

APR 97

5962-E441-12

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part

of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Copies of these documents are available online at

https://assist.dla.mil/quicksearch/

or from the Standardization Document

Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in

accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as

designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The

manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as

defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not

affect the form, fit, or function of the device for the applicable device class.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38534 and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.

3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4, 5, 6, and 7.

3.2.5 Block diagram. The block diagram shall be as specified on figure 8.

3.2.5 Typical output test circuit. The typical output test circuit shall be as specified on figure 9.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full specified operating temperature range.

STANDARD

MICROCIRCUIT DRAWING

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

SIZE

REVISION LEVEL

5962-94585

SHEET

DSCC FORM 2234

APR 97

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

3.5 Programming procedure. The programming procedure shall be as specified by manufacturer and shall be available on

request.

3.6 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with

the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked as listed in MIL-HDBK-103

and QML-38534.

3.7 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described

herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,

for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those

which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be

made available to the preparing activity (DLA Land and Maritime -VA) upon request.

3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this

drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the

manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.

3.9 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

microcircuits delivered to this drawing.

3.10 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This

reprogrammability test shall be done for the initial characterization and after any design or process changes which may affect

the reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of

program/erase endurance cycles listed in section 1.3 herein over the full specified operating temperature range. The vendor's

procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity.

3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall

be done for initial characterization and after any design or process change which may affect data retention. The methods and

procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military

temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of

the acquiring or preparing activity.

STANDARD

MICROCIRCUIT DRAWING

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

SIZE

REVISION LEVEL

5962-94585

SHEET

DSCC FORM 2234

APR 97

Recommended Resources

Noise box circuit (1)

DC relay delayed release circuit 2b

Cheap AC Signal Strip Scale Indicator Circuit Diagram

Proportional thermostat circuit

Exhaust gas concentration detection circuit

water level meter circuit

Sharing the replacement principles of rectifier diodes: What is a rectifier diode 　　Rectifier diode is a semiconductor device that can convert AC power into DC power. Rectifier diodes are widely used in various power rectifier circuits. When we choose a re...; 唯小样 Integrated technical exchanges

Apply for a trial of the LM3S8962 development board!: :)...; ansoneleven Microcontroller MCU

After RAS dial-up connection, an incorrect IP and subnet mask are obtained: I recently debugged a 3G network card. The driver under wince has been basically completed. The dial-up connection can also be established and it shows "connected" after dialing. However, I cannot ope...; litiantao Embedded System

Could you please come in and take a look and help?: Help: Please call my landline 0550-7764090 within half an hour after my post is published. This is the landline that comes with the fiber optic modem. If I turn off the fiber optic modem, you can't ac...; wangfuchong Talking

Dry goods income rules: [size=4][b]Introduction to the rules for earning from dry goods: [/b] In order to encourage everyone to publish and actively discover high-quality original posts, eeworld has launched a dry goods chan...; okhxyyo Suggestions & Announcements

STM32+MAX6675+K-type thermocouple temperature measurement: When using stm32+max6675+k-type thermocouple to measure the temperature of the transistor, the temperature can be displayed normally. However, when the Agilent power supply applies 0.1a current to the...; chloebb Analog electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components