ATC RF/Microwave Capacitors QPL Approved to MIL-PRF-55681 / 4 and 5
CDR
DESIGNATION: Identifies
established reliability, ceramic
dielectric, fixed, chip capacitors.
12
B
ATC PART NUMBER CODE:
G
101 A
F
W
S
FAILURE RATE LEVEL
(Established at 90% confidence):
M - - 1% per 1000 hours
P - - 0.1% per 1000 hours
R - - 0.01% per 1000 hours
S - - 0.001% per 1000 hours
STYLE: Identifies dimensions of the
capacitor and lead type, where applicable.
RATED TEMP: -55°C to +125°C
VOLTAGE TEMP. (TCC) LIMITS:
G = +90 ±20 PPM/°C; P = 0 ±30 PPM/°C
CAPACITANCE CODE: The first two digits represent
significant figures and the last digit specifies the number
of zeros to follow. When fractional values of pF are required,
the letter R shall be used to indicate the decimal point.
RATED DC VOLTAGE @ 125°C:
A - - 50 VDC, B - - 100 VDC, C - - 200 VDC,
D - - 300 VDC, E - - 500 VDC, K - - 150 VDC
TERMINATION FINISH:
N - Gold over Nickel over Silver (CDR11, CDR13)
S - Solder Coated, Final (CDR12, CDR14, CDR23, CDR25)
T - Silver (CDR21, CDR22, CDR24)
U - Solder Coated, Nickel Barrier (CDR12, CDR14)
N and U - Terminations preferred for best solder-
ability, thermocompression bonding, leach and mig-
ration resistance, and shelf life for chips and pellets.
W - Solder plated, nickel barrier (CDR12, CDR14, not
for new designs)
Z - Solder plated, nickel barrier (CDR12, CDR14)
CAPACITANCE TOLERANCE:
B (±0.1 pF), C (±0.25 pF), D (±0.5 pF), F (±1%),
G (±2%), J (+5%), K (±10%), M (±20%)
TYPE DESIGNATION*
TABLE I - STYLES CDR11 AND CDR12 CAPACITOR CHARACTERISTICS
CAPACITANCE
RANGE (pF)
CAPACITANCE
TOLERANCE
AVAILABLE
B
B, C
B, C, D
B, C, D
B, C, J, K, M
F, G, J, K, M
F, G, J, K, M
F, G, J, K, M
RATED TEMP. AND
VOLTAGE-TEMP.
LIMITS
Characteristic BG
(+90 ±20 PPM/°C)
and
Characteristic BP
(0 ±30 PPM/°C)
BP
RATED DC
VOLTAGE
CDR1-B-0R1KB-- to CDR1-B-0R2---B--
CDR1-B-0R3K--- to CDR1-B-0R4---
CDR1-B-0R5K--- to CDR1-B-2R2---**
CDR1-B-2R4K--- to CDR1-B-6R2---***
CDR1-B-6R8K--- to CDR1-B-9R1---***
CDR1-B-100K--- to CDR1-B-101K---***
CDR1-BP111K--- to CDR1-BP621---***
CDR1-BP681A--- to CDR1-BP102---***
0.1 pF to 0.2 pF
0.3 pF to 0.4 pF
0.5 pF to 2.2 pF
2.4 pF to 6.2 pF
6.8 pF to 9.1 pF
10 pF to 100 pF
110 pF to 620 pF
680 pF to 1000 pF
A = 50
K = 150
A = 50
B = 100
TABLE II - STYLES CDR13 AND CDR14 CAPACITOR CHARACTERISTICS
TYPE DESIGNATION*
CAPACITANCE
RANGE (pF)
0.1 pF to 0.2 pF
0.3 pF to 0.4 pF
0.5 pF to 2.2 pF
2.4 pF to 6.2 pF
6.8 pF to 9.1 pF
10 pF to 100 pF
110 pF to 200 pF
220 pF to 470 pF
510 pF to 620 pF
680 pF to 1000 pF
1100 pF to 5100 pF
CAPACITANCE
TOLERANCE
AVAILABLE
B
B, C
B, C, D
B, C, D
B, C, J, K, M
RATED TEMP. AND
VOLTAGE-TEMP.
LIMITS
RATED DC
VOLTAGE
CDR1-B-0R1EB-- to CDR1-B-0R2---B--
CDR1-B-0R3E--- to CDR1-B-0R4---
CDR1-B--0R5E--- to CDR1-B-2R2---**
CDR1-B-2R4E--- to CDR1-B-6R2---***
CDR1-B-6R8E--- to CDR1-B-9R1---***
CDR1-B-100E--- to CDR1-B-101---***
CDR1-B-111D--- to CDR1-B-201---***
CDR1-B-221C--- to CDR1-B-471C---***
CDR1-B-511B--- to CDR1-B-621---***
CDR1-B-681A--- to CDR1-B-102A---***
CDR1-BP112A--- to CDR1-BP512A---***
*
Characteristic BG
(+90 ±20 PPM/°C)
and
Characteristic BP
(0 ±30 PPM/°C)
C = 200
E = 500
F, G, J, K, M
BP
C = 200 D = 300
C = 200
A = 50 B = 100
A = 50
Complete type designation will include additional symbols to indicate style, voltage-temperature limits, capacitance tolerance
(where applicable), termination finish, and failure rate level.
** Intermediate values in this category are in 0.1 pF steps.
*** Intermediate values in each category are given by the RETMA 5% Table.
A M E R I C A N
T E C H N I C A L
ATC Europe
saleseur@atceramics.com
C E R A M I C S
ATC Asia
sales@atceramics-asia.com
2
ATC North America
sales@atceramics.com
w w w.a tc e r a m ics .c o m
ATC RF/Microwave Capacitors QPL Approved to MIL-PRF-55681 / 4 and 5
TABLE III - STYLES CDR21 TO CDR25 CAPACITOR CHARACTERISTICS
TYPE DESIGNATION*
CAPACITANCE
RANGE (pF)
0.1 pF to 0.2 pF
0.3 pF to 0.4 pF
0.5 pF to 2.2 pF
2.4 pF to 6.2 pF
6.8 pF to 9.1 pF
10 pF to 100 pF
110 pF to 200 pF
220 pF to 470 pF
510 pF to 620 pF
680 pF to 1000 pF
1100 pF to 5100 pF
CAPACITANCE
TOLERANCE
AVAILABLE
B
B, C
B, C, D
B, C, D
B, C, J, K, M
RATED TEMP. AND
VOLTAGE-TEMP.
LIMITS
RATED DC
VOLTAGE
CDR2-B-0R1EB-- to CDR2-B-0R2EB--
CDR2-B-0R3E--- to CDR2-B-0R4E---
CDR2-B--0R5E--- to CDR2-B-2R2E---**
CDR2-B-2R4E--- to CDR2-B-6R2E---***
CDR2-B-6R8E--- to CDR2-B-9R1E---***
CDR21-B-100E--- to CDR2-B-101E---***
CDR2-B-111D--- to CDR2-B-201D---***
CDR2-B-221C--- to CDR2-B-471C---***
CDR2-B-511B--- to CDR2-B-621B---***
CDR2-B-681A--- to CDR2-B-102A---***
CDR2-BP112A--- to CDR2-BP512A---***
*
Characteristic BG
(+90 ±20 PPM/°C)
and
Characteristic BP
(0 ±30 PPM/°C)
500 = E
F, G, J, K, M
BP
300 = D
200 = C
100 = B
50 = A
Complete type designation will include additional symbols to indicate style, voltage-temperature limits, capacitance tolerance
(where applicable), termination finish (T for styles CDR21, CDR22 and CDR24, and S for styles CDR23 and CDR25), and failure rate level.
Please note:
Leaded devices CDR 21 through CDR 25 are available to the R Failure Rate Level only.
** Intermediate values in this category are in 0.1 pF steps.
*** Intermediate values in each category are given by the RETMA 5% Table as follows: 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 75, 82, 91.
MECHANICAL CONFIGURATIONS
MIL-
PRF-55681
STYLES
CDR 11
CDR 13
CDR 12
CDR 14
CDR 12
CDR 14
CASE
SIZE
A
B
A
B
A
B
B
TYPE
Chip
L
OUTLINES
BODY DIMENSIONS
LENGTH
WIDTH
THICKNESS
LEAD AND TERMINATION
DIMENSIONS
AND MATERIALS
N - Gold Over Nickel
Over Silver
N is ATC’s UNI-TERM
®
CA
W
T
.055 ±.015
(1.4 ±0.38)
.110 ±.020
(2.79 ±0.51)
.055 ±.025
(1.4 ±0.63)
T
.020/.057
(0.51/1.45)
.030/.102
(0.76/2.59)
.020/.057
(0.51/1.45)
.030/.102
(0.76/2.59)
.020/.057
(0.51/1.45)
.030/.102
(0.76/2.59)
CA
Chip
Pellet
Pellet
W/T IS A
TERMINATION SURFACE
P
W
L
.055 ±.015
(1.4 ±0.38)
.110 ±.020
(2.79 ±0.51)
P
W/T IS A
TERMINATION SURFACE
.110 +.035 -.020
(2.79 +0.89 -0.51)
S - Solder Coated, Final
U - Solder Coated,
Nickel Barrier
U is ATC’s BARRIER//CAP
®
Solder Plate
W
W
L
WL
TL
LL
.055 ±.015
(1.4 ±0.38)
T
Solder Plate
W
W/T IS A
TERMINATION SURFACE
L
T
W
.110 ±.020
(2.79 ±0.51)
W - Nickel Barrier,
Solder Plate.
CDR 21
Microstrip
MS
WL
TL
LL
LENGTH
WIDTH
W
L
T
TL
LL
THICK-
NESS
CDR 22
B
AR
Axial
Ribbon
Radial
Ribbon
WL
W
L
LL
T
.250 (6.35)
min.
WL
.093
±.005
(2.36
±0.13)
.004
±.001
(0.10
±0.03)
CDR 24
B
RR
W
L
LL
T
TL
WL
.135 ±.015
(3.43 ±0.38)
.110 ±.015
(2.79 ±0.38)
.060/.100
(1.52/2.54)
(Termination T - Silver)
CDR 23
B
Radial
RW
Wire
Axial
Wire
W
L
T
• •
L
W
L
LL
T
W
LL
WL
CDR 25
B
AW
• •
L
LL
T
.50 (12.7)
min.
•
T
W
• •
L
LL
#26 AWG
.016 (.375)
dia. nom.
(Termination S - Solder Coated)
All leads and ribbon are silver and are attached with high temperature solder.
T
W
All dimensions are in inches, except those in parentheses which are in millimeters.
STYLE
CDR11
CDR12
CDR13
CDR14
EQUIV. ATC PART NO.
CHARACTERISTICS
• •
BG
BP
LL
STYLE
CDR21
CDR22
CDR23
CDR24
CDR25
W
•
L
T
EQUIV. ATC PART NO.
CHARACTERISTICS
BG
BP
100B ------ MS
100B ------ AR
100B ------ RW
100B ------ RR
100B ------ AW
700B ------ MS
700B ------ AR
700B ------ RW
700B ------ RR
700B ------ AW
100A
100A
100B
100B
700A
700A
700B
700B
A M E R I C A N
ATC North America
sales@atceramics.com
T E C H N I C A L
ATC Europe
saleseur@atceramics.com
C E R A M I C S
ATC Asia
sales@atceramics-asia.com
w w w.a t c e r am ic s .c o m
3
Sales of ATC products are subject to the terms and conditions contained in American Technical Ceramics Corp. Terms and Conditions of Sale(ATC document #001-992). Copies of these terms
and conditions will be provided upon request. They may also be viewed on ATC’s website at www.atceramics.com/productfinder/default.asp. Click on the link for Terms and Conditions of Sale.
ATC has made every effort to have this information as accurate as possible. However, no responsibility is assumed by ATC for its use, nor for any infringements of rights of third parties which
may result from its use. ATC reserves the right to revise the content or modify its product without prior notice.
From communications, computers, consumer electronics to automobiles and industry, from energy, medical care to security and aerospace, TI has integrated the advantages of both parties after acquiring ...
I am now designing a serial port data acquisition program. I hope that after each data acquisition, a prompt sound like a MESSAGEBOX pop-up will be emitted. Could you please tell me how to design it?...
Dear GGs and MMs, what methods do you use to measure speed? Please share if you are interested, hehe... There are many small car problems circulating. Do you think it is feasible? I think the possibil...
I recently used the LPCXpresso software and found that I had to add header files myself. It's so troublesome. Does anyone have some header file libraries for LPC1343? Can you share them? Thank you....
[b]Introduction[/b] Complex programmable logic devices (FPGAs) have been increasingly used in electronic design in recent years. FPGAs are particularly suitable for applications such as high-speed dat...
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
