Y162633R0000C9R datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> Y162633R0000C9R

Y162633R0000C9R: DescriptionFixed Resistor, Metal Foil, 0.3W, 33ohm, 95V, 0.25% +/-Tol, -.2,.2ppm/Cel, 1506,; CategoryPassive components The resistor; File Size2MB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y162633R0000C9R Overview

Fixed Resistor, Metal Foil, 0.3W, 33ohm, 95V, 0.25% +/-Tol, -.2,.2ppm/Cel, 1506,

Y162633R0000C9R Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	860437658
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Number of terminals	2
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	0.64 mm
Package length	3.81 mm
Package form	SMT
Package width	1.57 mm
method of packing	TR
Rated power dissipation(P)	0.3 W
resistance	33 Ω
Resistor type	FIXED RESISTOR
series	VSMP
size code	1506
technology	METAL FOIL
Temperature Coefficient	0.2 ppm/°C
Terminal surface	Tin/Silver/Copper - with Nickel barrier
Tolerance	0.25%
Operating Voltage	95 V

Preview

Download Datasheet

View All

VSMP Series (0603, 0805, 1206, 1506, 2010, 2018, 2512)

(Z-Foil)

Ultra High Precision Foil Wraparound Surface Mount Chip Resistor

with TCR of ± 0.05 ppm/°C and Power Coefficient of 5 ppm at

Rated Power and Load Life Stability of ± 0.005 % (50 ppm)

FEATURES



Temperature coefficient of resistance (TCR):

0.05 ppm/°C typical (0 °C to + 60 °C)

0.2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C ref.)



Resistance tolerance: to ± 0.01 %



Power coefficient “R due to self heating”:

5 ppm at rated power



Power rating: to 750 mW at + 70 °C (see table 3)



Load life stability: to ± 0.005 % at 70 °C, 2000 h at rated

power



Resistance range: 5



to 125 k (for lower or higher

values, please contact us)



Vishay Foil resistors are not restricted to standard values,

we can supply specific “as required” values at no extra cost

or delivery (e.g. 1K2345 vs. 1K)



Thermal stabilization time < 1 s



(nominal value achieved within 10 ppm of steady state

value)



Electrostatic discharge (ESD) at least to 25 kV



Short time overload:



0.005 %



Non inductive, non capacitive design



Rise time: 1 ns effectively no ringing



Current noise: 0.010 µV

RMS

/V of applied voltage

(< - 40 dB)



Voltage coefficient < 0.1 ppm/V



Non inductive: < 0.08 µH



Non hot spot design



Terminal finishes available: lead (Pb)-free, tin/lead alloy



Matched sets are available on request



Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vpgsensors.com

Top View

(for date code print specification please refer to table 2)

INTRODUCTION

VSMP Series is the industry’s first device to provide high

rated power and excellent load life stability along with

extremely low TCR — all in one resistor.

One of the most important parameters influencing stability is

the Temperature Coefficient of Resistance (TCR). Although

the TCR of foil resistors is considered extremely low, this

characteristic has been further refined over the years. The

VSMP Series utilizes ultra high precision Bulk Metal

Z-Foil.

The Z-Foil technology provides a significant reduction of the

resistive element’s sensitivity to ambient temperature

variations (TCR) and to self heating when power is applied

(Power Coefficient of Resistance, or PCR). Along with the

inherently low PCR and TCR, Z-Foil technology also

provides remarkably improved load life stability, low noise

and tight tolerances.

The VSMP resistor has a full wraparound termination which

assures secure contact during the manufacturing process,

as well as providing stability during multiple thermal cyclings.

Vishay Foil Resistors' (VFR) application engineering

department is available to advise and make

recommendations. For non-standard technical requirements

and special applications, please contact VFR using the

e-mail address in the footer below.

Percent of Rated Power

TABLE 1 - TOLERANCE AND TCR VS.

RESISTANCE VALUE

(1)

(- 55 °C to + 125 °C, + 25 °C Ref.)

RESISTANCE

VALUE

()

250to 125K

100to < 250

50to < 100

25to < 50

10to < 25

5 to < 10

TOLERANCE

(%)

± 0.01

± 0.02

± 0.05

± 0.1

± 0.25

± 0.5

TYPICAL TCR AND

MAX. SPREAD

(ppm/°C)

± 0.2 ± 1.8

± 0.2 ± 2.8

± 0.2 ± 3.8

± 0.2 ± 7.8

FIGURE 1 - POWER DERATING CURVE

- 55 °C

100

- 75

+ 70 °C

- 50

- 25

+ 25 + 50 + 75 + 100 + 125 + 150 + 175

Ambient Temperature (°C)

* Pb containing terminations are not RoHS compliant; exemptions

may apply

Note

(1)

For tighter performances and non-standard values lower than



and above 125K, please contact VFR’s application

engineering using the e-mail addresses in the footer below

Document Number: 63060

Revision: 3-Mar-15

For any questions, contact

foil@vpgsensors.com

www.vishayfoilresistors.com

Recommended Resources

Flash/light control circuit diagram

Adaptive DC Regulator

AM walkie-talkie transmitter circuit

Motor automatic restart circuit

STK085-105 power amplifier circuit

Practical circuit of full-bridge switching regulated power supply

Ask an old question: Change the debug serial port of the arm board to a normal serial port: I have searched for a long time, but they all say something different. I don't know which one is correct, so I'll open a thread to ask again. The board's serial port 1 is now used as a debug serial po...; hongyan ARM Technology

Problems with nested structures: I wrote the structure below, which is a structure array nested in a structure; the program is as follows: typedef struct { struct data TXBUF[CAN_TXBUF_LENGTH]; volatile uint32_t head; /*!< ReceiveData...; panzhenlkj NXP MCU

D-Class AMP Load RL Headphone Connection Problem: Dear experts, please tell me a question about the connection of headphones to Class D amplifier load As shown in the pictureThis is the case where one end of the earphone is connected to the output an...; jkairup Analog electronics

Is boundary alignment related to the compiler or the processor? How should I set boundary alignment? Thank you!: I would like to ask you, is the boundary alignment of the structure related to the compiler or the processor? My compiler is Tornado and the processor is PPC. Can anyone tell me how to set the boundar...; hefang0511 Embedded System

Help: How to solve the problem of inductor noise in boost circuit: [table=98%,rgb(239, 245, 249)] [tr][td][size=4]In the project, the battery is used for power supply. The HM1548 boost chip is used. The battery is used as input. When the battery power is not enough t...; 小浅白白 Power technology

Can't find your customized platform SDK when creating a new smart project in vs2005: I use WIN7 as my operating system, and installed VS2005+sp1. Now I use Zhou Ligong’s board, and I have installed my own SDK called EPC-8000. However, when I create a new project with VS2005, I only se...; 沙漠绿洲 Embedded System

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components