EEWORLDEEWORLDEEWORLD

Part Number

Search

G5798A

Description
500kHz 2A/3A Synchronous Step-down DC/DC
File Size69KB,1 Pages
ManufacturerGlobal Mixed-mode Technology
Websitehttp://www.gmt.com.tw
Download Datasheet Compare View All

G5798A Overview

500kHz 2A/3A Synchronous Step-down DC/DC

Global Mixed-mode Technology
G5798/G5798A
G5799/G5799A
General Description
The G5798/G5799 is a monolithic step-down switch mode
regulator with a built in internal power MOSFET. It achieves
2A/3A continuous output current over a wide input supply
range with excellent load and line regulation.
Current mode operation provides fast transient response
and eases loop stabilization.
Fault condition protection includes cycle-by-cycle current
limiting, output short circuit protection and thermal shut-
down. In shutdown mode the regulator draws 32µA of
supply current. Internal soft-start for output power up
ramp and minimizes the inrush supply current at initial
startup.
PG in G579X is open-drain pin detect from FB. When
FB>0.92XVref, PG is high impedance and FB<0.85XVref, PG
is low impedance.
G579XA add typical 220mS deglitch timeout period when
FB>0.92XVref to make sure PG signal.
The G5798/G5799 requires a minimum number of readily
available standard external components. It is available in
a SOP-8 (FD) package.
500kHz 2A/3A Synchronous Step-down DC/DC
Features
2A/3A Output Current
Internal 100mΩ RDS-ON High-Side and
100mΩ RDS-ON Low-Side Power Switches
Available two kinds of delay in PG
PG pin is detect FB until threshold then
immediately react in G579X
PG pin is detect FB until threshold then
delay 220mS react in G579XA
Stable with Low ESR Output Ceramic Capaci-
tors
32µA Shutdown Mode
Fixed 500kHz Frequency
Thermal Shutdown
Cycle-by-Cycle Over Current Protection
Wide 4.5V to 24V Operating Input Range
Vref =0.8V +-2%
Internal soft start
Available in SOP-8/SOP-8 (FD) Package
Applications
DSL Modems
Distributed Power Systems
Pre-Regulator for Linear Regulators
Ordering Information
ORDER
NUMBER
MARKING
PG DELAY TIME
No delay
delay 220mS
No delay
delay 220mS
TEMP.
RANGE
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PACKAGE
(Green)
SOP-8
SOP-8
SOP-8 (FD)
SOP-8 (FD)
G5798P11U
G5798
G5798AP11U
G5798A
G5799F11U
G5799
G5799AF11U
G5799A
Note: P1: SOP-8
F1: SOP-8 (FD)
1: Bonding Code
U : Tape & Reel
Pin Configuration
G5798/G5798A
BST
IN
SW
1
8
VCC
PG
BST
1
G5799/G5799A
8
VCC
PG
2
3
7
IN
SW
2
3
Thermal
Pad
7
6
EN
6
EN
GND
4
5
FB
GND
4
5
FB
SOP-8
SOP-8 (FD)
Note: Recommend connecting the Thermal Pad to
the Ground for excellent power dissipation.
Ver:0.92
Aug 05, 2013
TEL: 886-3-5788833
http://www.gmt.com.tw
1

G5798A Related Products

G5798A G5798 G5799 G5799A
Description 500kHz 2A/3A Synchronous Step-down DC/DC 500kHz 2A/3A Synchronous Step-down DC/DC 500kHz 2A/3A Synchronous Step-down DC/DC 500kHz 2A/3A Synchronous Step-down DC/DC
Can anyone help me understand the meaning of some statements in the 430 official library?
This is the external interrupt function in the TI official library. Can anyone tell me the function of these statements? #if defined(__TI_COMPILER_VERSION__) || defined(__IAR_SYSTEMS_ICC__) #pragma ve...
flashtt Microcontroller MCU
Calculating the inclination angle using LIS3DSH accelerometer
Use the 3-axis accelerometer lis3dsh to read acceleration data and convert it into inclination. The program MCU uses MSP430FR5969 soft I2CMCU program [code]/*******************************************...
littleshrimp MEMS sensors
ULINK2 debugging issues
Why can't I recognize the MCU when I use ulink2 to debug lm3S8962?...
zhang1234bbcc Microcontroller MCU
When the motor is turning, the waveform of the DC-DC power supply SW pin is questionable.
DC-DC powers the motor. Figure 3 shows the waveform of the SW pin of the DC-DC when the motor is powered on but not rotating; Figure 4 shows the waveform of the SW pin of the DC-DC at the moment when ...
xiaxingxing Analog electronics
How is the clock in 8962 controlled? There seems to be something wrong with the library function.
According to Zhou Ligong's instructions, the external crystal frequency is multiplied to 200M by the phase-locked loop and then divided by SYSDIV. Zhou Ligong's development board uses a 6M external cr...
eeleader Microcontroller MCU
FPGA program solidification problem
How to solidify the FPGA program into the memory card on the ARM side?...
Makefile FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 880  1421  1540  1888  2433  18  29  32  39  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号