up-converter that has a typical conversion gain of
11 dB, and an image rejection of greater than
15 dBc. The device includes a LO doubler and
buffer, and can be tuned to give 2LO leakage of
less than -15 dBm. Variable gain can be achieved
by adjusting the bias, with turn-down trajectories
optimized to maintain linearity and 2LO leakage
over the gain control range. At full gain, an OIP3 of
30 dBm is typical. It is ideally suited for 42 GHz
band point-to-point radios.
Each device is 100% RF tested to ensure
performance compliance. The part is fabricated
using an efficient pHEMT process.
Pin Configuration
1
Pin No.
1
2
3
4
5
6
Function
LO
V
G
3
V
D
3
V
G
1
V
D
1
V
G
2
V
D
2
RF
V
G
4
I* Input
I Input
Q Input
Q* Input
Ordering Information
Part Number
MAUC-010515-000000
MAUC-010515-TR0200
MAUC-010515-TR0500
MAUC-010515-001SMB
Package
Bulk Quantity
200 Piece Reel
500 Piece Reel
Sample Evaluation Board
7
8
9
10
11
12
13
1. The exposed pad centered on the package bottom must be
connected to RF, DC and thermal ground.
* Restrictions on Hazardous Substances, European Union Directive 2011/65/EU.
1
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAUC-010515
Up Converter
40.5 - 43.5 GHz
Electrical Specifications: RF Freq: 40.5 - 43.5 GHz, LO = 0 dBm, IF = -10 dBm,
V
D
= 4 V, I
D
1 = I
D
2 = 90 mA, I
D
3 = 120 mA, T
A
= 25°C
Parameter
Frequency Range (LO)
2
Frequency Range (IF)
LO Input Power (Plo)
Conversion Gain
Image Rejection
Output IP3
Spurious (2xLO) [tuned]
Spurious (1xLO)
Noise Figure
Input Return Loss (IF port)
Output Return Loss (RF Port)
LO Return Loss
Current (I
D
1 + I
D
2 + I
D
3)
Gate Voltage (V
G
4)
Gate Current (I
G
4)
3
Rev. V5
Units
GHz
GHz
dBm
dB
dBc
dBm
dBm
dBm
dB
dB
dB
dB
mA
V
mA
Min.
18.5
DC
0
8
-
25
-
-
-
-
-
-
-
-
-
Typ.
-
-
-
11
22
30
-40
-57
19
12
8
15
300
-3
4
Max.
21.75
3.5
8
16
-
-
-
-
-
-
-
-
400
-
-
2. LO frequency range limits the performance characteristics to USB only.
3. Adjust V
G
1, V
G
2, V
G
3 between -1.0 and -0.1 V to achieve specified current. Typical 300 mA = 90 (I
D
1) + 90 (I
D
2) + 120 (I
D
3)
Absolute Maximum Ratings
4,5,6
Parameter
Drain Voltage
Gate Bias Voltage (V
G
1,2,3)
Gate Bias Voltage (V
G
4)
Input Power
LO Input Power
Storage Temperature
Operating Temperature
Junction Temperature
7
Absolute Maximum
4.3 V
-1.5 V < V
G
< 0 V
-4.0 V < V
G
< 0 V
10 dBm
13 dBm
-55°C to +150°C
-40°C to +85°C
+150°C
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
Human Body Model Class 1B and Machine Model
Class B devices.
2
4. Exceeding any one or combination of these limits may cause
permanent damage to this device.
5. MACOM does not recommend sustained operation near these
survivability limits.
6. Operating at nominal conditions with T
J
≤ 150 °C will ensure
MTTF > 1 x 10
6
hours.
7. Junction Temperature (T
J
) = T
C
+ Ө
JC
* (V * I)
Typical thermal resistance (Ө
JC
) = 41.7 °C/W.
a) For T
C
= 25 °C, T
J
= 75.04 °C @ 4 V, 300 mA
b) For T
C
= 85 °C, T
J
= 135.04 °C @ 4 V, 300 mA
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAUC-010515
Up Converter
40.5 - 43.5 GHz
Typical Performance Curves:
V
D
= 4 V, I
D
1 = I
D
2 = 90 mA, I
D
3 = 120 mA, LO = 0 dBm, IF = -10 dBm, T
A
= 25°C
Conversion Gain @ 3.5 GHz IF
20
Rev. V5
Conversion Gain @ 2 GHz IF
20
15
15
10
10
5
+25°C
-40°C
+85°C
5
+25°C
-40°C
+85°C
0
40.5
41.0
41.5
42.0
42.5
43.0
43.5
0
40.5
41.0
41.5
42.0
42.5
43.0
43.5
Frequency (GHz)
Frequency (GHz)
IP3 @ 3.5 GHz IF
40
35
30
25
20
15
10
40.5
OIP3
IIP3
Output IP3 @ 2 GHz IF
40
35
30
25
20
15
10
40.5
+25°C
-40°C
+85°C
41.0
41.5
42.0
42.5
43.0
43.5
41.0
41.5
42.0
42.5
43.0
43.5
Frequency (GHz)
Frequency (GHz)
Image Rejection @ 3.5 GHz IF
35
30
25
20
15
10
40.5
41.0
41.5
42.0
42.5
43.0
43.5
Frequency (GHz)
3
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAUC-010515
Up Converter
40.5 - 43.5 GHz
Typical Performance Curves:
V
D
= 4 V, I
D
1 = I
D
2 = 90 mA, I
D
3 = 120 mA, LO = 0 dBm, IF = -10 dBm, T
A
= 25°C
IF Return Loss
0
Rev. V5
RF Return Loss
0
-5
-5
-10
-10
-15
-15
-20
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
-20
40.5
41.0
41.5
42.0
42.5
43.0
43.5
Frequency (GHz)
Frequency (GHz)
LO Return Loss
0
-5
-10
LO Leakage
-20
-30
1xLO
2xLO
-40
-15
-50
-20
-25
-30
18.0
-60
18.5
19.0
19.5
20.0
20.5
21.0
21.5
22.0
-70
18.75
19.00
19.25
19.50
19.75
20.00
Frequency (GHz)
Frequency (GHz)
4
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAUC-010515
Up Converter
40.5 - 43.5 GHz
Rev. V5
App Note [1] Biasing -
As shown in the Pin Designations table, the device is operated by biasing V
D
1, V
D
2, and
V
D
3 at 4 V. The corresponding drain currents are set to 90 mA, 90 mA, and 120 mA respectively. V
G
4 requires a
fixed voltage bias of nominally -3 V. It is recommended to use active bias on V
G
1 and V
G
2 to keep the currents in
V
D
1 and V
D
2 constant, in order to maintain the best performance over temperature. The LO multiplier can be
operated with either a fixed gate V
G
3 > -0.6 V or fixed current 120 mA. In either scenario the performance of the
part should be the same. Depending on the supply voltages available and the power dissipation constraints, the
bias circuits may include a single transistor or a low power operational amplifier, with a low value resistor in series
with the drain supply to sense the current. Make sure to sequence the applied voltage to ensure negative gate
bias is available before applying the positive drain supply.
App Note [2] I/Q versus I*/Q* -
The IF input to the typical configuration is through a 90° hybrid coupler. The
hybrid splits the IF input into inphase and quadrature phase components. These two signals enter the
MAUC-010515 on either the I/Q pair, or the I*/Q* complimentary pair. Whichever pair are not used must be
terminated into 50 Ω. There are subtle differences between the performance when using the main IF ports (I, Q)
versus the complimentary ports (I*, Q*). For highest gain, best image rejection and lowest noise figure, the main
IF ports (I, Q) should be used.
5
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit
www.macom.com
for additional data sheets and product information.
I am a little scared when I write this topic. I don't know if I can grasp the concept of value chain. I just want to talk about some small views on the entire embedded software industry. The term "val...
I took a look and it's better to share with you the general rules of wiring. The characteristics and general rules of automobile wiring are: generally a single-wire system is adopted, electrical equip...
Our company sells, repairs and maintains second-hand instruments and equipment, such as 8960 comprehensive tester, CMU200, network analyzer, spectrum analyzer, signal source and other instruments. The...
I want a perpetual calendar based on the C51 microcontroller. [font=宋体][size=10.5pt] This perpetual calendar can select the year, month, day, week, hour, minute, second, lunar calendar, solar calendar...
SinoWise's SH66xx series 4-bit microcontrollers have the characteristics of fast speed, low power consumption, simple structure, easy to use, and high cost performance. They are widely used in remo...[Details]
Microelectromechanical systems (MEMS) are gradually entering the consumer, industrial, medical, automotive and computer application markets. Moreover, we cannot ignore their steady progress in the ins...[Details]
As a branch of signal and information processing, digital signal processing has penetrated into various fields of scientific research, technological development, industrial production, national defens...[Details]
0 Introduction
Today, with the rapid development of electronic technology and the emergence of new multifunctional electric energy meters, the choice of memory in the electric energy m...[Details]
When using GPS for positioning, it will be affected by various factors. The factors that affect the accuracy of GPS positioning can be divided into the following four categories (see the figure be...[Details]
introduction
Usually, there are many input and output ports in RF systems, and it is expensive to use a multi-port network analyzer to analyze scattering characteristics. Therefore, it is ...[Details]
Application of TWLA500 in ADC and related fields
FAE: On-site technical support.
Provide technical support for the application of the products you sell, and handle quality issues ra...[Details]
1 Introduction
Intelligent software agents are software programs that can perform specific tasks for users, have a certain degree of intelligence, can autonomously perform some tasks, and ...[Details]
In recent years, with the rapid economic growth, wireless communication has developed rapidly. Since spread spectrum signals have the characteristics of anti-interference, confidentiality, anti-det...[Details]
Abstract:
Under high dynamic conditions, combined with GEC's twelve-channel correlator GP2021, this paper discusses the structural design of GPS receivers and the key technologies inv...[Details]
Abstract:
QT1101 is a QTouch charge transfer (QT) device, a complete digital controller that can detect signals when approaching or touching up to 10 independent keys. It can be widely used i...[Details]
Abstract: In many SCART applications, due to the complex signal switching requirements, dedicated ICs are usually used to implement SCART connections. This will bring cost pressure to single SCART ...[Details]
Abstract: This paper analyzes the technical characteristics of mobile streaming media and the core technical protocol of mobile streaming media - H.264 protocol, and explains the two major domesti...[Details]
Intelligent video analysis system is the development direction of monitoring. This technology is not far away from us. The 1,300 channels of the Qinghai-Tibet Railway use video analysis to protect ...[Details]
1. Overview
"The key to understanding the future of television is to stop viewing television as television. Thinking about television from the perspective of bits can bring it the greatest...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
