EEWORLDEEWORLDEEWORLD

Part Number

Search

54121-812201050LF

Description
Board Connector, 20 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size101KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54121-812201050LF Overview

Board Connector, 20 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,

54121-812201050LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid305704972
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL9.1
body width0.094 inch
subject depth0.413 inch
body length2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialPOLYETHYLENE
JESD-609 codee3
Manufacturer's serial number54121
Plug contact pitch0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts20
PDM: Rev:G
STATUS:
Released
Printed: Mar 10, 2011
.
MSP430 power consumption issues
MSP430G2231, I output a 38KHZ square wave signal with a duty cycle of 1/3, but the power consumption is still nearly 2 MA. Why is the power consumption still so high? Please give me some advice. TACCR...
yyhhgg Microcontroller MCU
Why does the output voltage of an op amp need to be offset? Analysis of the principle of differential circuit
The differential operational amplifier circuit effectively suppresses the common-mode signal and only amplifies the differential signal, so it is widely used.Circuit Configuration of Differential Circ...
infinigo Integrated technical exchanges
[Mill MYC-J1028X development board trial] Use Node-RED to transform the MYC-J1028X development board into an industrial control gateway
[i=s]This post was last edited by HonestQiao on 2022-10-2 10:59[/i]This article is long and involves many knowledge points. You need to read it patiently. The following is the directory of specific co...
HonestQiao NXP MCU
How to transfer Q, I, and M registers to V register in PLC program?
[size=3]Please give me some advice on how to transfer Q, I, M registers to V register in PLC program[/size]...
eeleader Industrial Control Electronics
CCS3.3 Chinese Learning Manual
I have uploaded two Chinese learning manuals for CCS3.3, I hope they will be helpful to everyone!...
kooking DSP and ARM Processors
Programs written in EVC cannot open the GPIO driver when operated under wince5.0
I used evc to write a gpio output program, but when I opened the driver with wince system, it showed that the gpio driver failed to be opened. I don't know why. I used the s3c2440 experimental board o...
gaoli.85 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 791  988  1071  2826  208  16  20  22  57  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号