EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTS-242-D-B-10-G-120-LT

Description
Board Connector, 84 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size181KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTS-242-D-B-10-G-120-LT Overview

Board Connector, 84 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle

BSTS-242-D-B-10-G-120-LT Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1164468090
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresBOARD STACKING CONNECTOR
body width0.158 inch
subject depth0.12 inch
body length3.318 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedGold Flash (Au) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial numberBSTS
Plug contact pitch0.079 inch
Match contact row spacing0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.0066 mm
Plating thickness10u inch
Rated current (signal)2 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.18 inch
Terminal pitch2.0066 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts84
How to set the pin pull-up resistor (weak pull-up) in Quartus II
When using Altera's FPGA , due to system requirements, it is necessary to add pull-up resistors inside the pins. This can be set in the Assignment Editor in the Quartus II software . The specific proc...
eeleader FPGA/CPLD
【Help】Sensor selection for a certain op amp circuit
[i=s]This post was last edited by ddasd on 2021-11-30 10:47[/i]To explain briefly, I work in industrial control, and my knowledge of electronics and analog circuits is limited to professional courses ...
ddasd Analog electronics
Different power modules have different output powers for the same load
Help: Recently, I used a 5-to-5 power module to power a CAN communication circuit. When using two different 5-to-5 power modules, the power output of the power module is quite different. Note: 1. The ...
rabbit-cricket Power technology
Jiangsu Province Electronic Design Competition Topic A
[i=s] This post was last edited by paulhyde on 2014-9-15 04:01 [/i] What do you think about the Jiangsu Province Electronic Design Competition A? Also, what is the frequency of the noise file?...
caohuajie Electronics Design Contest
[F7 Design Team Recruitment] Reflective Blood Oxygen Heart Rate Signal Acquisition and Monitoring Recording System
[i=s]This post was last edited by nemo1991 on 2015-8-28 11:41[/i] Blood oxygen sensor display:The original blood oxygen meter based on single chip microcomputer, the amplifier circuit is based on disc...
nemo1991 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1604  650  2476  1302  2709  33  14  50  27  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号