Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
C1096_MIL-PRF-32535_X7R • 8/26/2021
2
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
High Reliability Surface Mount Capacitors, MIL-PRF-32535, 4 – 100 VDC (X7R Dielectric)
Packaging C-Spec Ordering Options Table
Packaging Type
1
Standard Packaging (Waffle Tray)
7" Tape & Reel
1
Packaging/Grade
Ordering Code (C-Spec)
Not required (blank)
Contact Sales
Default packaging with no C-Spec is “Waffle Tray,” and is recommended for order quantities of less than 250 pieces. See Waffle Tray packaging
information section for additional details.
1
See Tape & Reel Packaging information section of the datasheet for additional details.
Dimensions per MIL-PRF-32535 – Inches (Millimeters)
W
L
T
B
S
EIA
Size
Code
0402
0603
0805
1
1206
2
1210
2
1812
2
2220
2
1
Metric
Size
Code
1005
1608
2012
3216
3225
4532
5650
L
Length
0.040+0.006/−0.004
(1.02+0.15/−0.10)
0.063+0.008/−0.006
(1.60+0.2/−0.15)
0.079+0.012/−0.01
(2.01+0.3/−0.25)
0.126+0.012/−0.01
(3.20+0.3/−0.25)
0.126+0.012/−0.01
(3.20+0.3/−0.25)
0.178±0.012
(4.52±0.30)
0.224±0.016
(5.69±0.41)
W
Width
0.020+0.005/−0.004
(0.51+0.13/−0.10)
0.032+0.008/−0.006
(0.81+0.2/−0.15)
0.050+0.012/−0.01
(1.27+0.3/−0.25)
0.063+0.012/−0.01
(1.60+0.3/−0.25)
0.098+0.012/−0.010
(2.49+0.3/−0.25)
0.126±0.012
(3.20±0.30)
0.197±0.016
(5.00±0.41)
T
Thickness
0.025
(0.64)
0.040
(1.02)
0.062
(1.57)
0.071
(1.8)
0.110
(2.79)
0.110
(2.79)
0.110
(2.79)
B
Bandwidth
0.004 (0.100)
Minimum
0.016 ±0.008
(0.41±0.20)
0.020±0.010
(0.51±0.25)
0.020±0.014
(0.51±0.36)
0.020±0.014
(0.51±0.36)
0.024±0.018
(0.61±0.46)
0.025±0.018
(0.64±0.46)
Maximum
Part Weight
(mg)
3
1.6
6.3
20
57
108
216
430
Mounting
Technique
Solder reflow
only
Solder wave or
solder reflow
Solder reflow
only
For EIA 0805 solder dipped termination finish, add 0.020 (0.51) to the positive length tolerance and 0.015 (0.38) to the positive width and thickness
tolerance.
2
For EIA 1206, 1210, 1812 and 2220 solder dipped termination finishes, add 0.025 (0.64) to the positive length tolerance and 0.015 (0.38) to the positive
width and thickness tolerance.
3
Maximum Part Weight represents the maximum weight in the given case size for all voltages.
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
The most important components of new energy electric vehicles are power batteries, electric motors and energy conversion control systems. The power battery must achieve high performance such as fas...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
HL201A is a special thick film driver integrated circuit with a capacity of less than 75AGTR developed by Xi'an Power Electronics Technology Research Institute. The article explains the pin arrange...[Details]
0 Introduction
The load with impact (rapid change) power in the power system will cause the voltage fluctuation and flicker of the power grid, causing many electrical equipment to fail to wo...[Details]
京公网安备 11010802033920号
EEWORLD
