EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342M09B2B23PT1

Description
RESISTOR, THIN FILM, 1 W, 0.1 %, 300 ppm, 2230 ohm, SURFACE MOUNT, 2512, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342M09B2B23PT1 Overview

RESISTOR, THIN FILM, 1 W, 0.1 %, 300 ppm, 2230 ohm, SURFACE MOUNT, 2512, CHIP

M55342M09B2B23PT1 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1766807473
package instructionSMT, 2512
Reach Compliance Codeunknown
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.3
Other featuresNON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length6.5786 mm
Package formSMT
Package width3.1496 mm
method of packingTR
Rated power dissipation(P)1 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance2230 Ω
Resistor typeFIXED RESISTOR
size code2512
surface mountYES
technologyTHIN FILM
Temperature Coefficient300 ppm/°C
Terminal surfaceTIN LEAD OVER NICKEL
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage200 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
I want to talk about drone batteries
[i=s]This post was last edited by qwqwqw2088 on 2016-10-9 22:39[/i] UAVs have expanded from the military field to the civilian field, especially being widely used in agriculture, forestry, electricity...
qwqwqw2088 Analogue and Mixed Signal
【NUCLEO-L552ZE Review】+ Based on FREERTOS transplantation
I've been playing with the L552 board recently, and suddenly I wanted to use FREERTOS. I wanted to port it myself, but when I looked online, I found that most of the posts were based on the porting of...
紫色的天空 stm32/stm8
Haha, look at the product on Taobao, 28 yuan
...
chenzhufly DIY/Open Source Hardware
DM642 hard interrupt delay problem
[size=5]Problem description: [/size] [size=5]During system debugging, it was found that hardware interrupts often fail to respond in time. Based on the phenomenon, it is inferred that the interrupt wi...
fish001 DSP and ARM Processors
Do I need to add anything else to input logic signals into FPGA?
I am making a logic signal analyzer. I would like to ask whether I need to add protection measures when inputting the logic signal to be tested into FPGA, such as optical isolation. Will adding optica...
白丁 FPGA/CPLD
Fortunately, I applied for it. How can I start learning Helper2416 as a complete novice? !
[b]I was fortunate enough to apply for the Helper2416 development board. I am a complete novice. I have only played with STM32F1 and UCOS III for a while, and I don’t know anything else. I saw the mas...
yuer_52 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 975  2864  731  2522  227  20  58  15  51  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号