EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AS-07-3521-DA

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 3520ohm, 100V, 0.5% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AS-07-3521-DA Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 3520ohm, 100V, 0.5% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AS-07-3521-DA Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802675376
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance3520 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
Why do two different forms of simulation in modelsim work but one doesn't?
Dear experts, I use the simulation software of modelsim 6.5, and use two methods for simulation: 1. Create a project in quartus, input the module under test, set the relevant options, and get ***.vo a...
大萝卜的小蝌蚪 FPGA/CPLD
【SensorTile】Basic construction of the environment
[i=s]This post was last edited by michael_llh on 2017-1-8 19:37[/i] [align=left][font=微软雅黑][size=3] Let’s see what preparations should be made for the development of SensorTile? [/size][/font][/align]...
michael_llh ST Sensors & Low Power Wireless Technology Forum
A basic problem of serial port driver
ARM S3C2410 CPU "In FIFO mode, once the data in the FIFO reaches a certain trigger level, an interrupt is generated." After this interrupt is generated, the CPU is notified by the interrupt source, an...
foxyboss Embedded System
Calculation of wireless communication distance
Here is a calculation method for wireless communication distance in free space propagation: Free space propagation refers to the propagation of radio waves when there is an infinite vacuum around the ...
Jacktang Wireless Connectivity
IoT Smart Home-Kitchen Hardware Debugging
Talking about the hardware debugging of the kitchen part, it was quite bumpy!1. Start by drawing the PCB diagram. Due to the limitation of the board area, various components are destined to be crowded...
anananjjj DIY/Open Source Hardware
Typical Applications of LM358 Dual Operational Amplifier Circuit
Typical Applications of LM358 Dual Operational Amplifier CircuitPin arrangement diagramDescription:The LM358 contains two independent, high-gain, internally frequency-compensated dual operational ampl...
fighting Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2083  2826  2314  327  1264  42  57  47  7  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号