[size=5]1. I decided on a direction: software direction[/size] [size=4] I graduated more than two years ago, and I have been working on MCU software, hardware, PCB, testing, etc. It is too complicated...
Have you ever encountered this situation? The program compiles fine and passes the simulation, but if you add one or two lines of code that have no effect, the program compiles and passes, but the sim...
[i=s]This post was last edited by ylyfxzsx on 2016-8-21 16:04[/i] [font=Tahoma, Helvetica, SimSun, sans-serif]Now according to the analysis of netizens, it is very likely to be a smart bracelet produc...
[i=s]This post was last edited by qwqwqw2088 on 2020-1-17 08:34[/i]By: Hayden Hast – Systems EngineerWhen I first visited a Texas barbecue restaurant, I was so surprised by the variety of meats on the...
This is the interrupt function that enters the early wake-up (in the program's development board routine)void WWDG_IRQHandler(void) { u8 wr,tr; wr=WWDG-CFR0X7F; tr=WWDG-CR0X7F; if(trwr) WWDG_Set_Count...
Have you ever encountered data frame loss when doing SPI communication? Among multiple frames of data, one or more frames of data are always not received....
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
