85°C ± 2°C, 85%±5%RH, 1000 hours; 1.5 hr ON, 0.5 hr OFF cycle
85°C ± 2°C, 3000 hours, 1.5 hr ON, 0.5 hr OFF cycle
+155°C, 1000 hours
* Depends on resistance value, please contact KOA Speer for details.
Precautions for Use
• The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts
absorb on the top tapes to cause a failure in the mounting and the parts are destructed by static electricity (1J, 2A, 2B, 2E: 1kV and more, 1E: 0.5kV and more at Human
Body Model 100pF, 1.5kΩ) to change the resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged
on the tapes. Similarly, care should be given not to apply the excessive static electricity when mounting on the boards.
• Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc.
The flux may contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na＋), chlorine (Cl−) etc. Therefore these
kinds of ionic substances may induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since
lead free solder contains ionic substances. Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
• Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk
may happen that the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of
protecting coat may be dropped down. Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
• Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. 5~35°C/35~75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like
hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
●
The upper electrodes could be peeled off when a heat-resistant masking tape is attached to the mounted chip resistors and then detached from them. It is confirmed that
the adhesiveness gets stronger due to the exposure to heat under mounting. Accordingly, we recommend the use of masking tape be refrained. If the use of heat-resistant
masking tape is unavoidable, please make sure that the adhesives on the tape do not directly come in contact with the product.
For Surface Temperature Rise Graph see Environmental Applications. Additional environmental applications can also be found at www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
11/06/17
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
[i=s]This post was last edited by Jackzhang1992 on 2015-4-17 15:13[/i] [align=center][font=宋体](IV) Software and Hardware Design of Tetris Game[/font][/align][align=left][font=宋体][b]Overview[/b][/font]...
The mystery of the skyrocketing housing prices in small and medium-sized cities. To laymen, the skyrocketing housing prices are incomprehensible and incredible. However, as real estate professionals, ...
Getting down to business - Understanding MLC machine learning of LSM6DSOX
Before learning, I referred to justd0's post (https://bbs.eeworld.com.cn/thread-1120851-1-1.html). I have to say that it is re...
I want to burn the program into the external memory using quartus ii. The external memory is not the dedicated EPCS but winbond. How to operate it? I have read a lot on the Internet but I am still con...
I use STM32 to make a light source controller. I hope to save some of the related settings in Flash so that I can read them directly when I start the computer next time, saving the trouble of resettin...
[i=s]This post was last edited by Jacktang on 2020-5-8 23:19[/i]0. Introduction Radio Frequency Identification (RFID) technology is an emerging automatic identification technology. It uses wireless r...
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
The automotive power electronics market has grown rapidly as comfort and active safety features become more common. As traditional mechanical functions shift to electronic applications, the demand ...[Details]
1 Introduction
At present, people have higher and higher requirements for the quality of life. When people are busy with work, soymilk machine is a new type of household beverage machine. It uses so...[Details]
1 Introduction
At present, advocating health has become the focus of people's attention, and the emergence of treadmills has become more and more popular. People can exercise at home or in the ...[Details]
introduction
The air compressor unit in the operating area of a lead-zinc mine in Guangdong is a key equipment in mining production. There are six imported Ingersoll Rand CENTAC air compress...[Details]
Today, automakers are integrating more and more complex electronic systems into cars. Allied Business Intelligence predicts that annual sales of the automotive semiconductor market will rise from $...[Details]
Current sensing in automotive applications includes controlling the current through solenoids and injectors. For example, during diesel injection, we rapidly increase the current to the induction i...[Details]
(1) Open circuit voltage of the battery
(2) Internal resistance of the battery
(3) Battery operating voltage
(4) Charging voltage
Charging voltage refers to the voltage applied ...[Details]
1 Introduction
The coke oven gas recovery system is mainly composed of a gas tank and a pressure reducing station. While realizing the recycling and reuse of coke oven gas, it also plays an imp...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
