1. Serial port 232 chipMAX232cse chip introduction
RS232 interface chip MAX232, SOP package mainly has the following models: MAX232CSE, MAX232ESE. If the suffix letter is "C", it means commercial grad...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:12[/i] I got it working today. May I ask what wireless transceiver modules everyone uses? I think it might be useful for the car problem!...
The controlled circuit is 48V/10A DC, and I want to control the microcontroller to trigger the switch of the relay through the computer serial port. But I checked the market and found that they are ge...
[i=s] This post was last edited by RF-刘海石 on 2016-12-27 22:40 [/i] [color=#ff0000][size=4]2016 is about to end, but I am still on a business trip, working hard in this cold northwest. . . I probably w...
TO-252 package, the first pin is connected to two resistors for voltage division, the second and third pins are measured with a multimeter and are Schottky diodes, but what is the first pin used for?...
Error: L6286E: Value(0xbffff70) out of range(0 - 0xfff) for relocation #2 (wrt symbol Image$$ZI$$Limit) in init.o(init)================================================================================M...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]