The UT54ACS374 and the UT54ACTS374 are non-inverting
octal D type flip-flops with three-state outputs designed for driv-
ing highly capacitive or relatively low-impedance loads. The
device is suitable for buffer registers, I/O ports, and bidirectional
bus drivers.
The eight flip-flops are edge triggered D-type flip-flops. On the
positive transition of the clock the Q outputs will follow the data
(D) inputs.
An output-control input (OC) places the eight outputs in either
a normal logic state (high or low logic level) or a high-impedance
state. The high-impedance third state and increased drive pro-
vide the capability to drive the bus line in a bus-organized system
without the need for interface or pull-up components.
The output control OC does not affect the internal operations of
the flip-flops. Old data can be retained or new data can be en-
tered while the outputs are off.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
INPUTS
OC
L
L
L
H
CLK
↑
↑
L
X
nD
H
L
X
X
OUTPUT
nQ
H
L
nQ
0
Z
Note:
1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and IEC
Publication 617-12.
OC
1Q
1D
2D
2Q
3Q
3D
4D
4Q
V
SS
20-Pin DIP
Top View
OC
1Q
1D
2D
2Q
3Q
3D
4D
4Q
V
SS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
DD
8Q
8D
7D
7Q
6Q
6D
5D
5Q
CLK
20-Lead Flatpack
Top View
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
DD
8Q
8D
7D
7Q
6Q
6D
5D
5Q
CLK
LOGIC SYMBOL
OC
CLK
(1)
(11)
EN
C1
1D (3)
(4)
2D
3D (7)
(8)
4D
5D (13)
6D (14)
7D (17)
8D (18)
1D
(2)
1Q
(5)
2Q
(6) 3Q
(9)
(12)
(15)
(16)
(19)
4Q
5Q
6Q
7Q
8Q
1
LOGIC DIAGRAM
8D
(18)
7D
(17)
6D
(14)
5D
(13)
4D
(8)
3D
(7)
2D
(4)
1D
(3)
CLK OC
(11) (1)
DC
Q
D C
Q
DC
Q
D C
Q
D C
Q
D C
Q
D C
Q
D C
Q
(19)
8Q
7Q
(16)
(15)
6Q
(12)
5Q
4Q
(9)
3Q
(6)
2Q
(5)
(2)
1Q
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
×C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Three-state output leakage current
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
ΔI
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
1.9
10
1.6
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
-20
20
.5V
DD
.7V
DD
-1
1
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
0.40
0.25
V
V
OH
V
μA
I
OZ
I
OS
I
OL
-200
8
200
mA
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
大家请看看 ：
@echo off
@REM --------------------------------------------------------------------------
@REM Copyright (c) Wolfson Microelectronics plc.All rights reserved.
@REM
@REM This software as well a...
The progress of industrial modernization in mainland China and the continuous high-speed growth of the electronic information industry at a rate of more than 20% have driven the rapid growth of the se...
I am using AAEON's x86 board - PFM540I. I used the provided Windows GeodeLX BSP to customize and generate a debug version image. After downloading it via Ethernet using the debug network card, the Out...
New sewer generatorA college student was inspired by a hydroelectric power station and designed and invented this hydroelectric generator. This generator is installed on the vertical sewer in the buil...
[align=left][color=#000] Author: [color=rgb(98, 98, 98)]Art Kay[/color][/color][/align][align=left][color=000] There is a long-standing debate about the use, or overuse, of [color=rgb(205, 23, 31)]SPI...
In the forum, I often see some new friends feeling sad because they cannot download paid apps because they do not have Chip Coins.
I just saw a post about an LCD1602 display based on 89C51 and other p...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
Reflow soldering is a critical process in electronics assembly production, and the cleanliness of the reflow oven has a direct impact on product quality. Dust and residue accumulation within the ov...[Details]
As more and more consumers purchase new energy vehicles, the safety of electric vehicles has become a major concern. This has been particularly prominent following a series of electric vehicle fire...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
Current Development Status of DVR Market
A DVR, or digital video recorder, uses a hard disk for recording, unlike traditional analog video recorders. It's often called a DVR because it's a com...[Details]
According to foreign media reports, secondary battery materials company POSCO Future M announced that it has successfully developed two experimental (prototype) positive electrode materials for the...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
When discussing autonomous driving technology, there are often two extremes: on the one hand, there's the vision of "fully autonomous driving," while on the other, there's concern about potential s...[Details]
This paper proposes a temperature real-time transmission and display solution based on LED optical data transmission, with Jingwei Yager low-power FPGA HR (Yellow River) series as the main controll...[Details]
Electric vehicles are becoming increasingly popular, with increasingly longer ranges. There are two ways to charge electric vehicles: slow charging and fast charging. Which is the most suitable? Sl...[Details]
In daily life, power transformers have different functions and uses due to different usage scenarios. The most common ones can be divided into: control transformers, isolation transformers, rectifi...[Details]
Plug-in hybrid vehicles (PHEVs) utilize two powertrains. Their pure electric range is typically inferior to that of pure electric vehicles, often reaching less than half that. Currently, mainstream...[Details]
Consumer demand for premium listening experiences has driven rapid evolution in the wireless headphone market in recent years. Hybrid designs, which utilize two drivers per earbud to enhance sound ...[Details]
0 Introduction
With a rapidly aging population, a young couple is now required to care for an increasing number of elderly people, leading to a growing difficulty in providing care for them. E...[Details]
In this final installment of a five-part blog series, I will discuss noise in op amps driving headphone loads and some techniques for reducing it. Previous posts have discussed headphone load power...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
