Operating Temperature Range ......................... -40°C to +105°C
Junction Temperature ......................................................+150°C
Storage Temperature Range ............................ -65°C to +150°C
Lead Temperature (soldering, 10s) ................................. +300°C
Soldering Temperature (reflow) .......................................+260°C
*GATE
is internally driven and clamped. Do not drive GATE with external source.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(V
CC
, EN (MAX5924/MAX5925), EN1 (MAX5926) = +2.7V to +13.2V;
EN2
(MAX5926) = 0V; V
S
(see Figure 1) = +1.05V to V
CC
;
T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at V
CC
= 5V, R
L
= 500Ω from OUT to GND, C
L
= 1μF, SLEW = open,
T
A
= +25°C, unless otherwise noted.) (Note 1)
PARAMETER
POWER SUPPLIES
V
CC
Operating Range
V
S
Operating Range
Supply Current
SYMBOL
V
CC
I
CC
V
UVLO
t
D,UVLO
R
LP
V
LP,TH
I
CB
t
LP
2.7V < V
CC
< 5V
t
DG
V
S
CONDITIONS
MIN
2.7
V
S
as defined in Figure 1
1.0
1.5
1.73
123
4
3
43
172
2.06
900
200
30
10
102
200
37
34
30
45
40
40
40
50
37
40
60
50
60
50
60
42
50
80
60
80
60
70
µA
350
65
20
205
235
FET is fully enhanced, SC_DET = V
CC
Default value, V
S
and V
CC
increasing, Figure 1
(Note 2)
TYP
MAX
13.2
V
CC
2.5
UNITS
V
V
mA
V
µs
ms
Ω
ms
mV
UNDERVOLTAGE LOCKOUT (UVLO)
UVLO Threshold
V
CC
UVLO Deglitch Time
LOAD-PROBE
V
CC
UVLO Startup Delay
Load-Probe Resistance (Note 3)
Load-Probe Timeout
Load-Probe Threshold Voltage
CIRCUIT BREAKER
2.47
5V < V
CC
< 13.2V
(Note 4)
TC = high (MAX5926), V
CC
= 2.7V and V
CB
= 1V
MAX5924
2.7V ≤ V
CC
≤ 13.2V
V
CC
= 2.7V, V
CB
= 1V,
T
A
= +25°C
TC = low
(MAX5926),
MAX5925 (Note 5)
V
CC
= 2.7V, V
CB
= 1V, T
A
= +105°C
(MAX5925D)
2.7V ≤ V
CC
≤ 13.2V,
T
A
= +25°C
2.7V ≤ V
CC
≤ 13.2V,
T
A
= +105°C (MAX5925D)
Circuit-Breaker Programming
Current
I
CB25
I
CB85
TC = low
(MAX5926),
MAX5925 (Note 5)
V
CC
= 2.7V and
V
CB
= 1V, T
A
= +85°C
2.7V ≤ V
CC
≤ 13.2V,
T
A
= +85°C
www.maximintegrated.com
Maxim Integrated
│
2
MAX5924/MAX5925/
MAX5926
Electrical Characteristics (continued)
1V to 13.2V, n-Channel Hot-Swap Controllers
Require No Sense Resistor
(V
CC
, EN (MAX5924/MAX5925), EN1 (MAX5926) = +2.7V to +13.2V;
EN2
(MAX5926) = 0V; V
S
(see Figure 1) = +1.05V to V
CC
;
T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at V
CC
= 5V, R
L
= 500Ω from OUT to GND, C
L
= 1μF, SLEW = open,
T
A
= +25°C, unless otherwise noted.) (Note 1)
PARAMETER
Circuit-Breaker Programming
Current During Startup
Circuit-Breaker Enable Threshold
Circuit-Breaker Comparator Offset
Voltage
Fast Circuit-Breaker Offset
Resistor
Slow Circuit-Breaker Delay
Fast Circuit-Breaker Delay
Circuit-Breaker Trip Gate Pulldown
Current
Circuit-Breaker Temperature
Coefficient
OUT Current
MOSFET DRIVER
SYMBOL
I
CB,SU
V
CB,EN
V
CB_OS
R
CBF
t
CBS
t
CBF
Figure 3
V
CB
- V
SENSE
= 10mV
V
CB
- V
SENSE
= 500mV
V
GATE
= 2.5V, V
CC
= 13.2V, T
A
= -40°C to
+85°C
V
GATE
= 2.5V, V
CC
= 13.2V, T
A
= -40°C to
+105°C (MAX5925D)
MAX5924, TC = high (MAX5926)
MAX5925, TC = low (MAX5926)
13.5
12
1.2
0.95
V
GATE
- V
OUT
, rising gate voltage (Note 6)
2.3
CONDITIONS
MIN
TYP
2 x I
CB
3.6
0.3
1.9
1.6
280
27
27
0
3300
120
2.7V ≤ V
CC
≤ 13.2V, T
A
= -40°C to +85°C
External Gate Drive
V
GS
V
GATE
- V
OUT
2.7V ≤ V
CC
≤ 13.2V,
T
A
= -40°C to +105°C
(MAX5925D)
4.65
±4.7
2.7
2.95
MAX
UNITS
µA
V
mV
kΩ
ms
ns
mA
mA
ppm/°C
µA
I
GATE,PD
TC
ICB
I
OUT
4.2
4.0
2.19
239
0.747
0.747
5.5
5.5
9.5
0.84
7.2
V
7.2
V/ms
µA
Load Voltage Slew Rate
Gate Pullup Current Capacity
ENABLE COMPARATOR
EN, EN1 Reference Threshold
EN, EN1 Hysteresis
EN, EN1 Input Bias Current
DIGITAL OUTPUTS (PGOOD,
PGOOD)
Power-Good Output Low Voltage
Power-Good Output Open-Drain
Leakage Current
Power-Good Trip Point
Power-Good Hysteresis
SR
I
GATE
SLEW = open, C
GATE
= 10nF
V
GATE
= 0V
C
SLEW
= 300nF, C
GATE
= 10nF (Note 8)
V
EN/UVLO
V
EN,HYS
I
EN
V
OL
I
OH
V
PG,HYS
V
EN
(MAX5924/MAX5925) or
V
EN1
(MAX5926) rising, T
A
= -40°C to +85°C
V
EN
(MAX5925D) rising,
T
A
= -40°C to +105°C
EN (MAX5924/MAX5925) = V
CC
,
EN1 (MAX5926) = V
CC
I
OL
= 1mA
PGOOD/PGOOD = 13.2V
0.795
0.795
30
±8
0.3
0.2
0.850
V
0.875
mV
±50
0.4
1
4.7
nA
V
µA
V
V
V
THPGOOD
V
GATE
- V
OUT
, rising gate voltage
V
CB_EN
3.6
0.36
www.maximintegrated.com
Maxim Integrated
│
3
MAX5924/MAX5925/
MAX5926
Electrical Characteristics (continued)
1V to 13.2V, n-Channel Hot-Swap Controllers
Require No Sense Resistor
(V
CC
, EN (MAX5924/MAX5925), EN1 (MAX5926) = +2.7V to +13.2V;
EN2
(MAX5926) = 0V; V
S
(see Figure 1) = +1.05V to V
CC
;
T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at V
CC
= 5V, R
L
= 500Ω from OUT to GND, C
L
= 1μF, SLEW = open,
T
A
= +25°C, unless otherwise noted.) (Note 1)
LOGIC AND TIMING (TC, LATCH (MAX5926),
EN2
(MAX5926)
Autoretry Delay
Input Voltage
Input Bias Current
Time to Clear a Latched Fault
Note
Note
Note
Note
Note
1:
2:
3:
4:
5:
t
RETRY
V
IH
V
IL
Autoretry mode
PARAMETER
SYMBOL
CONDITIONS
MIN
0.6
2.0
0.4
Logic high at 13.2V
MAX5924A/MAX5924B
MAX5925A/MAX5925B
MAX5926 in latched mode
3
200
TYP
1.6
MAX
3.3
UNITS
s
V
µA
µS
I
BIAS
T
CLR
All devices are 100% tested at T
A
= +25°C and +85°C. All temperature limits at -40°C are guaranteed by design.
V
CC
drops 30% below the undervoltage lockout voltage during t
DG
are ignored.
R
LP
is the resistance measured between V
CC
and SC_DET during the load-probing phase, t
LP
.
Tested at +25°C and +85°C. Guaranteed by design at -40°C.
The circuit-breaker programming current increases linearly from V
CC
= 2.25V to 5V. See the Circuit-Breaker Current vs.
Supply Voltage graph in the
Typical Operating Characteristics.
Note 6:
See the
Startup Mode
section for more information.
Note 7:
V
GATE
is clamped to 17V (typ) above ground.
Note 8:
dv/dt = 330 x 10-9/C
SLEW
(V/ms), nMOS device used for measurement was IRF9530N. Slew rate is measured at the load.
Power Design Tips 40: Common-Mode Current of Non-Isolated Power Supplies : https://training.eeworld.com.cn/course/478Power Tip 40: Common-Mode Current in Non-Isolated Power Supplies...
I want to use F107 to read the audio file on the SD card, and then use the IIS interface to play the audio. Is this solution correct? Is it feasible? I am not familiar with the IIS interface and have ...
Description of the problem phenomenon: When using the STM32VET6 serial port 1, the interrupt returns the received data immediately after receiving the data. Use the host computer serial port debugging...
[color=#000]How to use an op amp to convert a 10mA AC small signal current into a 5A AC large current signal? The frequency is 50-60HZ, and the linearity is required to be relatively good. What op amp...
1. Background:
The instrument system parameter detection and control of the chemical production workshop of Tangshan Coal Gas Coking Plant are all analog instruments, some of which are eve...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
As a simple and practical input device, buttons have been used in various microcontroller application systems and are ubiquitous. However, the buttons used in different practical occasions are also...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
The emergence and development of street lamps are inseparable from the prosperity and progress of cities, which makes street lamps useful. Conversely, street lamps also make the night of the city n...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
Mobile phones, MP3s, tablet computers, laptops, digital cameras, handheld game consoles, navigation devices, etc., all these mobile devices are powered by mobile batteries, and the battery life is ...[Details]
Dual Tone MultiFrequency (DTMF) signaling is gradually being used in push-button telephones around the world. It quickly replaced the dial pulse signaling used in traditional rotary phones because ...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
