DS1267BS-100+ datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> converter> DS1267BS-100+

DS1267BS-100+: Descriptiondigital potentiometer ics; CategoryAnalog mixed-signal IC converter; File Size266KB，13 Pages; ManufacturerMaxim; Websitehttps://www.maximintegrated.com/en.html; Environmental Compliance

Download Datasheet Parametric Compare View All

DS1267BS-100+ Overview

digital potentiometer ics

DS1267BS-100+ Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Parts packaging code	SOIC
package instruction	SOP, SOP16,.4
Contacts	16
Reach Compliance Code	compli
ECCN code	EAR99
Factory Lead Time	6 weeks
control interface	3-WIRE SERIAL
Converter type	DIGITAL POTENTIOMETER
JESD-30 code	R-PDSO-G16
length	10.3 mm
Number of functions	2
Number of positions	256
Number of terminals	16
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package body material	PLASTIC/EPOXY
encapsulated code	SOP
Encapsulate equivalent code	SOP16,.4
Package shape	RECTANGULAR
Package form	SMALL OUTLINE
Peak Reflow Temperature (Celsius)	NOT SPECIFIED
power supply	5 V
Certification status	Not Qualified
resistance law	LINEAR
Maximum resistor tolerance	20%
Maximum resistor terminal voltage	6 V
Minimum resistor terminal voltage	-6 V
Maximum seat height	2.65 mm
Nominal supply voltage	5 V
surface mount	YES
Nominal temperature coefficient	750 ppm/°C
Temperature level	INDUSTRIAL
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	NOT SPECIFIED
Nominal total resistance	100000 Ω
width	7.5 mm
Base Number Matches	1

Preview

Download Datasheet

View All

DS1267B

Dual Digital Potentiometer

FEATURES

Two digitally controlled, 256-position

potentiometers

Serial port provides means for setting and

reading both potentiometers

Resistors can be connected in series to

provide increased total resistance

16-pin SO and 20-pin TSSOP packages

Resistive elements are temperature

compensated to ±0.3 LSB relative linearity

Standard resistance values:

– DS1267B-10 ~ 10kΩ

– DS1267B-50 ~ 50kΩ

– DS1267B-100 ~ 100kΩ

Operating Temperature Range:

– Industrial: -40°C to +85°C

PIN ASSIGNMENT

RST

CLK

GND

OUT

16-Pin SO (300-mil)

See Mech. Drawings Section

PIN DESCRIPTIONS

L0, L1

H0, H1

W0, W1

OUT

RST

CLK

OUT

GND

Low End of Resistor

High End of Resistor

Wiper Terminal of Resistor

Substrate Bias Voltage

Stacked Configuration Output

Serial Port Reset Input

Serial Port Data Input

Serial Port Clock Input

Cascade Port Output

+5V Supply

Ground

No Internal Connection

RST

CLK

GND

OUT

20-Pin TSSOP (173-mil)

PART NO.

DS1267BE-010+

DS1267BE-050+

DS1267BE-100+

DS1267BS-010+

DS1267BS-050+

DS1267BS-100+

PIN-

PACKAGE

20 TSSOP

16 SO

END-TO-END

RESISTANCE (kΩ)

100

19-6589; Rev 1; 1/14

Maxim Integrated

DS1267B

DESCRIPTION

The DS1267B Dual Digital Potentiometer Chip consists of two digitally controlled, solid-state

potentiometers. Each potentiometer is composed of 256 resistive sections. Between each resistive section

and both ends of the potentiometer are tap points which are accessible to the wiper. The position of the

wiper on the resistive array is set by an 8-bit value that controls which tap point is connected to the wiper

output. Communication and control of the device are accomplished via a 3-wire serial port interface. This

interface allows the device wiper position to be read or written.

Both potentiometers can be connected in series (or stacked) for an increased total resistance with the

same resolution. For multiple-device, single-processor environments, the DS1267B can be cascaded or

daisy-chained. This feature provides for control of multiple devices over a single 3-wire bus.

The DS1267B is offered in three standard resistance values which include 10kΩ, 50kΩ, and 100kΩ

versions. Available packages for the device include a 16-pin SO and 20-pin TSSOP.

OPERATION

The DS1267B contains two 256-position potentiometers whose wiper positions are set by an 8-bit value.

These two 8-bit values are written to a 17-bit I/O shift register that is used to store the two wiper positions

and the stack select bit when the device is powered. A block diagram of the DS1267B is presented in

Figure 1.

Communication and control of the DS1267B are accomplished through a 3-wire serial port interface that

drives an internal control logic unit. The 3-wire serial interface consists of the three input signals:

RST

CLK, and DQ.

The

RST

control signal is used to enable the 3-wire serial port operation of the device. The chip is

selected when

RST

is high;

RST

must be high to begin any communication to the DS1267B. The CLK

signal input is used to provide timing synchronization for data input and output. The DQ signal line is

used to transmit potentiometer wiper settings and the stack select bit configuration to the 17-bit I/O shift

Figure 9(a) presents the 3-wire serial port protocol. As shown, the 3-wire port is inactive when the

RST

signal input is low. Communication with the DS1267B requires the transition of the

RST

input from a

low state to a high state. Once the 3-wire port has been activated, data is entered into the part on the low

to high transition of the CLK signal inputs. Three-wire serial timing requirements are provided in the

timing diagrams of Figure 9(b)-(c).

Data written to the DS1267B over the 3-wire serial interface is stored in the 17-bit I/O shift register (see

Figure 2). The 17-bit I/O shift register contains both 8-bit potentiometer wiper position values and the

stack select bit. The composition of the I/O shift register is presented in Figure 2. Bit 0 of the I/O shift

Stacked

Configuration.

Bits 1 through 8 of the I/O shift register contain the potentiometer-1 wiper position value.

Bit 1 contains the MSB of the wiper setting for potentiometer-1 and bit 8 the LSB for the wiper setting.

Bits 9 through 16 of the I/O shift register contain the value of the potentiometer-0 wiper position, with the

MSB for the wiper position occupying bit 9 and the LSB bit 16.

DS1267B

The C

OUT

output of the DS1267B can be used to drive the DQ input of another DS1267B. When

connecting multiple devices, the total number of bits transmitted is always 17 times the number of

DS1267Bs in the daisy chain.

An optional feedback resistor can be placed between the C

OUT

terminal of the last device and the first

DS1267B DQ input, thus allowing the controlling processor to read as well as write data or circularly

clock data through the daisy chain. The value of the feedback or isolation resistor should be in the range

from 2Ω to 10kΩ.

When reading data via the C

OUT

pin and isolation resistor, the DQ line is left floating by the reading

device. When

RST

is driven high, bit 17 is present on the C

OUT

pin, which is fed back to the input DQ

pin through the isolation resistor. When the CLK input transitions low to high, bit 17 is loaded into the

first position of the I/O shift register and bit 16 becomes present on C

OUT

and DQ of the next device. After

17 bits (or 17 times the number of DS1267Bs in the daisy chain), the data has shifted completely around

and back to its original position. When

RST

transitions to the low state to end data transfer, the value (the

same as before the read occurred) is loaded into the wiper-0, wiper-1, and stack select bit I/O register.

ABSOLUTE AND RELATIVE LINEARITY

Absolute linearity, also known as integral nonlinearity, is defined as the difference between the actual

measured output voltage and the expected output voltage. Figure 5 presents the test circuit used to

measure absolute linearity. Absolute linearity is given in terms of a minimum increment or expected

output when the wiper is moved one position. In the case of the test circuit, a minimum increment (MI) or

one LSB would equal 10/512 volts. The equation for absolute linearity is given as follows:

(1)

ABSOLUTE LINEARITY (INL)

AL={V

(actual) - V

(expected)}/MI

Relative Linearity, also known as differential nonlinearity, is a measure of error between two adjacent

wiper position points and is given in terms of MI by equation (2).

(2)

RELATIVE LINEARITY (DNL)

RL={V

(n+1) - V

(n)}/MI

Figure 6 is a plot of absolute linearity and relative linearity versus wiper position for the DS1267B at

25°C. The specification for absolute linearity of the DS1267B is ±0.75 MI typical. The specification for

relative linearity of the DS1267B is ±0.3 MI typical.

Maxim Integrated .............................................................................................................................................................................................

DS1267BS-100+ Related Products

	DS1267BS-100+	DS1267BE-010+T/R	DS1267BS-050+	DS1267BE-100+T/R	DS1267BS-050+T/R	DS1267BS-100+T/R	DS1267BE-100+	DS1267BS-010+
Description	digital potentiometer ics	digital potentiometer ics digital sextet potentiometer	digital potentiometer ics	IC DGTL POT 100K 2CH 20TSSOP	IC DGTL POT 50K 2CH 16SOIC	IC DGTL POT 100K 2CH 16SOIC	IC DGTL POT 100K 2CH 20TSSOP
Is it Rohs certified?	conform to	conform to	conform to	conform to	conform to	conform to	conform to	conform to
Reach Compliance Code	compli	compli	compli	compliant	compliant	compliant	compliant	compliant
ECCN code	EAR99	EAR99	EAR99	EAR99	EAR99	EAR99	EAR99	EAR99
Factory Lead Time	6 weeks	6 weeks	6 weeks	6 weeks	9 weeks	6 weeks	6 weeks	6 weeks
Converter type	DIGITAL POTENTIOMETER	DIGITAL POTENTIOMETER	DIGITAL POTENTIOMETER	DIGITAL POTENTIOMETER	DIGITAL POTENTIOMETER	DIGITAL POTENTIOMETER	DIGITAL POTENTIOMETER	DIGITAL POTENTIOMETER
Base Number Matches	1	1	1	1	-	-	1	1

Recommended Resources

Optical communication receiving circuit diagram

Audio recorder recording and playback circuit

One of the thyristor turn-on delay circuits

Fluorescent lamp electronic ballast circuit one

Computer motherboard circuit diagram 440GX_06

Computer motherboard circuit diagram 815 4_40

lm3s811 uart: I used the board's virtual serial port to test communication and it was normal. However, when I connected MAX3232 to UART0 and UART1 to communicate with the computer, the UART0 data received by the se...; xupz123 Microcontroller MCU

Urgent! Please answer the question about STM32 CAN communication: I recently made a stm32 board, and the can is not working. Please help me.The situation is like this. The peripheral circuit of the can chip SN65HVD230 works normally. I use an experimental board (I h...; xujualiang stm32/stm8

ADC Research of msp430F5438A: Since the ADC module is needed in the project, it is necessary to study the ADC module. This is the description of ADC on the first page of the msp430F5428A datasheet: 12-Bit Analog-to-Digital Convert...; fish001 Microcontroller MCU

I am preparing to learn embedded system, please give me some suggestions, thank you: I have worked on OI before, and have a certain understanding of algorithms and data structures. I am familiar with C and x86ASM. Later, I became interested in hacking skills, Linux, and network, and l...; chenjinmei Embedded System

Power Design Tip 39: Synchronous Rectification Brings More Than Just High Efficiency: [flash]http://player.youku.com/player.php/sid/XMzY1NzQ4Mjcy/v.swf[/flash]Have you ever been asked to design a power supply with good load transient response at light loads? If so, and you allow the po...; 德州仪器 Analog electronics

Is there anyone who can guess what this chip is? I asked 5 websites and no one could figure it out.: [i=s]This post was last edited by bingworld on 2015-6-8 18:45[/i] I'm looking for an expert, I still don't understand what U1 is, the circuit diagram is in the attachment: Y1 is a transducer chip, the...; bingworld Analog electronics

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components