As we are anxious that our customers should benefit from the latest developments in the technology and standards,
AVX reserves the right to modify the characteristics published in this brochure.
NOTICE: Specifications are subject to change without notice. Contact your nearest AVX Sales Office for the latest specifications. All statements,
information and data given herein are believed to be accurate and reliable, but are presented without guarantee, warranty, or responsibility of any kind,
expressed or implied. Statements or suggestions concerning possible use of our products are made without representation or warranty that any such
use is free of patent infringement and are not recommendations to infringe any patent. The user should not assume that all safety measures are
indicated or that other measures may not be required. Specifications are typical and may not apply to all applications.
1
NTC Thermistors
General Characteristics
1 – INTRODUCTION
NTC thermistors are thermally sensitive resistors made from
a mixture of Mn, Ni, Co, Cu, Fe oxides. Sintered ceramic
bodies of various sizes can be obtained. Strict conditions
of mixing, pressing, sintering and metallization ensure an
excellent batch-to-batch product characteristics.
This semi-conducting material reacts as an NTC resistor,
whose resistance decreases with increasing temperature.
This Negative Temperature Coefficient effect can result from
an external change of the ambient temperature or an inter-
nal heating due to the Joule effect of a current flowing
through the thermistor.
By varying the composition and the size of the thermistors,
a wide range of resistance values (0.1Ω to 1MΩ) and tem-
perature coefficients (-2 to -6% per °C) can be achieved.
RoHS (Restriction of Hazardous Substances - European
Union directive 2002/95/EC).
ELV (End of Life-Vehicle - European Union directive
2000/53/EC).
All Thermistor Products have been fully RoHS/ELV since
before 2006.
Chip Thermistor NB RoHS/ELV Status: external Plating
100% smooth semi-bright Sn as standard SnPb Termination
available on request.
2.1.2. Temperature -
Resistance characteristics R (T)
This is the relation between the zero power resistance and
the temperature. It can be determined by experimental mea-
surements and may be described by the ratios R (T) /R
(25°C) where:
R (T)
is the resistance at any temperature T
R (25°C) is the resistance at 25°C.
These ratios are displayed on pages 29 to 33.
2.1.3. Temperature coefficient (α)
The temperature coefficient ( ) which is the slope of the
curve at a given point is defined by:
=
100
dR
•
R
dT
and expressed in % per °C.
2.1.4. Sensitivity index (B)
The equation R = A exp (B/T) may be used as a rough
approximation of the characteristic R (T).
B is called the sensitivity index or constant of the material
used.
To calculate the B value, it is necessary to know the resis-
tances R
1
and R
2
of the thermistor at the temperatures
T
1
and T
2
.
1 1
The equation: R
1
= R
2
exp B T - T
1
2
R
1
1
leads to:
B (K) =
• n
1-1
R
2
T T
2
1
Conventionally, B will be most often calculated for tempe-
ratures T
1
= 25°C and T
2
= 85°C (298.16 K and 358.16 K).
In fact, as the equation R = A exp (B/T) is an approximation,
the value of B depends on the temperatures T
1
and T
2
by
which it is calculated.
For example, from the R (T) characteristic of material M
(values given on page 29), it can be calculated:
B (25 – 85) = 3950
B (0 – 60) = 3901
B (50 – 110) = 3983
When using the equation R = A exp (B/T) for this material,
the error can vary by as much as 9% at 25°C, 0.6% at 55°C
and 1.6% at 125°C.
Using the same equation, it is possible to relate the values of
the index B and the coefficient
α:
(
)
2 – MAIN CHARACTERISTICS
2.1 CHARACTERISTICS WITH NO DISSIPATION
2.1.1. Nominal Resistance (Rn)
The nominal resistance of an NTC thermistor is generally
given at 25°C. It has to be measured at near zero power
so that the resultant heating only produces a negligible
measurement error.
The following table gives the maximum advised measure-
ment voltage as a function of resistance values and thermal
dissipation factors.
This voltage is such that the heating effect generated by the
measurement current only causes a resistance change of
1%
ΔRn/Rn.
Ranges of
values
(Ω)
R 10
10 < R 100
100 < R 1,000
1,000 < R 10,000
10,000 < R 100,000
R < 100,000
(
)
( )
Maximum measuring voltage
(V)
δ
= 2 mW/°C
δ
= 5 mW/°C
δ
= 10 mW/°C
δ
= 20 mW/°C
0.13
0.38
1.1
3.2
9.7
0.18
0.53
1.5
4.6
14.5
0.10
0.24
0.24
2.0
=
1
-B
1
dR =
•
• A exp (B/T) • T
2
A exp (B/T)
R
dT
B
= – T
2
expressed in %/°C
0.25
0.73
2.1
6.4
thus
2
NTC Thermistors
General Characteristics
2.1.5. Further approximation of R (T) curve
The description of the characteristic R (T) can be improved
by using a greater number of experimental points, and by
using the equation:
1 = A + B ( n R) + C ( n R)
3
T
The parameters A, B and C are determined by solving the
set of equations obtained by using the measured resis-
tances at three temperatures.
The solution of the above equation gives the resistance at
any temperature:
2
n R (T) = 1 3 - 27 A- 1/T + 3 3 27 A- 1/T + 4 B
3
C
C
C
2
2
Thus, the tolerance on the resistance ( R
2
/R
2
) at a temper-
ature T
2
is the sum of two contributions as illustrated on
Figure 1:
– the tolerance R
1
/R
1
at a temperature T
1
used as a
reference.
– an additional contribution due to the dispersion on
the characteristic R (T) which may be called
“Manufacturing tolerance” (Tf).
Graph with B
RΩ
Graph with B
±
ΔB
[
(
)
( (
2
) ())
R
25
3
- 3 + 27 A- 1/T + 3
C
2
2
(
)
3
B
1/T
(
27
(
A-C
)
+ 4
(
C
) )
]
3
}
(ΔR)
25°C
The precision of this description is typically 0.2°C for the
range –50 to +150°C (A, B, C being determined with exper-
imental values at –20, +50 and 120°C) or even better if this
temperature range is reduced. The ratios R(T)/R(25°C) for
each of the different materials shown on pages 29 to 33
have been calculated using the above method.
}
(ΔR)
+
}
T
F
25°C
}
= (ΔR)
T
25°C
T
Temperature (°C)
2.1.6. Resistance tolerance and temperature
precision
An important characteristic of a thermistor is the tolerance
on the resistance value at a given temperature.
This uncertainty on the resistance (DR/R) may be related to
the corresponding uncertainty on the temperature (DT),
using the relationship:
R 1
T = 100 • R •
Example: consider the thermistor ND06M00152J —
• R (25°C) = 1500 ohms
• Made from M material
• R (T) characteristic shown on page 23 gives:
= - 4.4%/°C at 25°C
• Tolerance R/R = ±5% is equivalent to:
T = 5%/4.4%/°C = ±1.14°C
Figure 1
Differentiating the equation R = A exp (B/T), the two contri-
butions on the tolerance at T can also be written:
R
2
= R
1
+
⎪
1 - 1
⎪
• B
T T
2
1
R
1
R
2
The T(f) values given with the resistance – temperature
characteristics on pages 29 to 33 are based on a computer
simulation using this equation and experimental values.
2.1.8. Designing the resistance tolerances
Using the fact that the coefficient decreases with temper-
ature (α = –B/T
2
), it is generally useful to define the closest
tolerance of the thermistor at the maximum value of the
temperature range where an accuracy in °C is required.
For example, let us compare the two designs 1 and 2
hereafter:
T
(°C)
0
25
55
85
100
2.1.7. Resistance tolerance at any temperature
Any material used for NTC manufacturing always displays a
dispersion for the R (T) characteristic.
This dispersion depends on the type of material used
and has been especially reduced for our accuracy series
thermistors.
R
(Ω)
3275
1000
300
109
69.4
α
(%/°C)
-5.2
-4.4
-3.7
-3.1
-2.9
Design 1
R/R(%)
3.5
3.0
3.5
4.1
4.5
Design 2
R/R(%)
5.0
4.5
4.0
3.4
3.0
T(°C)
0.7
0.7
1.0
1.3
1.6
T(°C)
1.0
1.1
1.1
1.1
1.0
Only the Design 2 is able to meet the requirement
ΔT
from 25°C to 100°C.
1°C
3
NTC Thermistors
General Characteristics
2.1.9. Shaping of the R (T) characteristic
By the use of a resistor network, it is possible to modify the
R (T) characteristic of a thermistor so that it matches the
required form, for example a linear response over a restrict-
ed temperature range.
A single fixed resistor Rp placed in parallel with a thermistor
gives a S–shape resistance–temperature curve (see Figure 2)
which is substantially more linear at the temperature range
around the inflexion point (Ro, To).
R
(kΩ)
R
TO
R
p
2.2 CHARACTERISTICS WITH ENERGY
DISSIPATION
When a current is flowing through an NTC thermistor, the
power due to the Joule effect raises the temperature of the
NTC above ambient.
The thermistor reaches a state of equilibrium when the
power supplied becomes equal to the power dissipated in
the environment.
The thermal behavior of the thermistor is mainly dependent
on the size, shape and mounting conditions.
Several parameters have been defined to characterize these
properties:
R
p
2.2.1. Heat capacity (H)
The heat capacity is the amount of heat required to change
the temperature of the thermistor by 1°C and is expressed in
J/°C.
2.2.2. Dissipation factor ( )
R
O
This is the ratio between the variation in dissipated power
and the variation of temperature of the NTC. It is expressed
in mW/°C and may be measured as:
U.I
=
85 – 25
T
O
T (°C)
Figure 2 – Linearization of a thermistor
where U.I is the power necessary to raise to 85°C the tem-
perature of a thermistor maintained in still air at 25°C.
2.2.3. Maximum permissible temperature (T max)
It can be calculated that better linearization is obtained when
the fixed resistor value and the mid-range temperature are
related by the formula:
B – To
Rp = R x
To
B+ 2To
For example, with a thermistor ND03N00103J —
R
25°C
= 10kΩ, B = 4080 K
good linearization is obtained with a resistor in parallel where
the value is:
4080 - 298
Rp = 10,000 Ω x
= 8088 Ω
4080 + (2 x 298)
This is the maximum ambient temperature at which the ther-
mistor may be operated with zero dissipation. Above this
temperature, the stability of the resistance and the leads
attachment can no longer be guaranteed.
2.2.4. Maximum permissible power at 25°C (Pmax)
This is the power required by a thermistor maintained in still
air at 25°C to reach the maximum temperature for which it is
specified.
For higher ambient temperatures, the maximum permissible
power is generally derated according to the Figure 3 here-
after and TL = Tmax – 10°C.
2.1.10. Demonstration of the R (T) parameters
calculation
To help our customers when designing thermistors for
temperature measurement or temperature compensation,
software developed by our engineering department is avail-
CC430F5137 has a small RAM. Some large arrays need to be defined in flash to save RAM space. The const keyword can be used to define arrays in flash. The two arrays sin_tab[512] and cos_tab[512] are o...
The main purpose of this system is to realize some simple automatic control functions in the car through the application of single-chip microcomputer. With MC68HC908GP single-chip microcomputer as the...
[align=left][align=center][media=x,500,375]https://training.eeworld.com.cn/course/4069/learn#lesson/9427[/media][/align][/align] [align=left][font=宋体]The above is a display of the work. If you can't w...
Good idea, cook hot pot with your phone, eat well and don't play with your phone! : https://training.eeworld.com.cn/course/3544
You have to put your phone in to heat up the hot pot. This is a great id...
[i=s]This post was last edited by reayfei on 2021-7-18 23:48[/i]1. Because the program shown in the figure can only be downloaded through FOTA, and not JLINK, you must understand the FOTA method.2. Us...
reayfeionsemi and Avnet IoT Innovation Design Competition
On April 20, the Photovoltaic Summit, guided by Jiangsu Renewable Energy Industry Association, hosted by Growatt, and supported by LONGi Solar Technology Co., Ltd. and Jiangsu Bigo New Energy Group...[Details]
1. Principle 1. Infrared emission protocol The infrared transmission protocol has been written in the previous article , so I will not repeat it here. 2. Timer counting and input capture A timer...[Details]
I have read the source code of mbed these days, and the interface encapsulation for upper-level application calls is quite good. The code quality is relatively high, the comments are also very detai...[Details]
1. Usage scenarios In the first case, when using a common STM32 delay function, similar to HAL_Delay(time), since this function uses a loop to judge and delay, when executing this function, the ent...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
On April 18-19, 2018, at the "Second Distributed Photovoltaic Carnival" held in Hangzhou, Jinko Power and China New Energy Assets Investment, Financing and Trading Platform (hereinafter referred to as...[Details]
There has been a lot of news about Huawei
phones
recently
. At the
Huawei
Global Analyst Conference
on the 17th
,
Huawei
announced that it will launch
5G
phones
in the seco...[Details]
China Energy Storage Network News:
On the 7th, Jurong Economic Development Zone signed a strategic cooperation framework agreement on comprehensive energy services with State Grid Jiangsu Int...[Details]
The adoption of vehicle tracking systems for cars and fleets is increasing. Modern trackers have reduced form factors and increased functionality to support active data transmission for real-time tra...[Details]
Recently, Jiangsu GoodWe Power Technology Co., Ltd. ("GoodWe") unveiled two products of the SDT family, the 17kW smart photovoltaic inverter GW17KN-DT and the 20kW smart photovoltaic inverter GW20KN-D...[Details]
The ZTE incident has aroused people's concerns about the future of Chinese chips, and they have been using WeChat and Weibo to express their views; the Chinese display industry is also worried abou...[Details]
ADC Introduction: ADC (Analog-to-Digital Converter). That is, converting analog signals into digital signals for processing. When storing or transmitting, analog-to-digital converters are almost ...[Details]
STM32 has two watchdogs: independent watchdog and window watchdog. This article mainly introduces the use of independent watchdog. Independent watchdog (IDWG): driven by an independent 40KHZ low-sp...[Details]
Why does MCU have a watchdog? With this question, let's learn about watchdogs. Even the 51 single-chip microcomputer has a watchdog, which shows that this dog has a special meaning to us. The purpose...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
