For latest revision and Regional Customer Service,
visit our website at www.te.com.
1
of 4
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
ORIGINAL INSTRUCTIONS
408-8501
3.2. Application Tooling
Power for seating tools must be provided by a machine capable of supplying a downward force of 45 Newtons
(N) [10 lb.] per contact. Manual Electric Servo Press (MEP 6T) 1585699-1, Bench Top Electric Servo Presses
(BMEP 3T) 1585697-1, and (BMEP 5T) 1585696-1 are available for this seating tool. For information on the
presses, visit the press-fit assembly equipment website at
http://tooling.te.com/pressfit.asp.
CAUTION
Over-driving of the connector will deform parts critical to the quality of the connection. Maximum force occurs prior to the
connector bottoming on the pc board.
4. SEATING
1. Set seating height to the dimension shown in Figure 2 (application tool
shut height
will equal the tool
seating height PLUS the combined thicknesses of the pc board and support fixture). After seating, a
gap of no more than 0.10 mm [.004 in.] between the connector standoffs and the pc board is allowed.
NOTE
The seating height of 38.1 mm [1.50 in.] is a reference starting point. Seating height may need adjusted to obtain the 0.1 mm
[.004 in.] maximum gap between the connector and the pc board.
2. Position the connector on the pc board so that contacts are properly aligned with the holes in the pc
board and pc board support fixture.
3. Sit the connector onto pc board until the open section of the contacts are resting securely on, but have
not fully entered, the holes in the pc board.
4. Orient the key(s) of the blade with the groove(s) on the inside of the connector housing, then position
the seating tool onto the connector, making sure the blade bottoms on the housing floor.
CAUTION
Damage to the pc board, seating tool, or connector may occur if the wrong seating tool is used, if the seating height is
improperly set, or if the seating tool is not properly seated in the connector before cycling the ram. DO NOT use damaged
product.
5. Center the seating tool (with the connector) under the ram of the applicator tool; and slowly lower the
ram until it just meets the seating tool. Verify alignment of the pc board support fixture, pc board,
connector, and seating tool.
6. Cycle the ram according to instructions included with the application tooling. Check the connector for
proper seating using the requirements in Application Specification
114-13059.
7. Remove the pc board or reposition the pc board and pc board support fixture for seating additional
connectors.
NOTE:
Not to Scale
Applicator Ram (Fully Down)
(Ref)
Seating Tool
Seating Height
(Connector Seated)
38.1 [1.50] Ref
Applicator Tooling
Shut Height
(Ram Down)
Maximum
Gap Allowed
0.10 [.004]
Blade Inside Connector
Housing and Bottomed
on Housing Floor
Contacts in Holes in PC Board
and PC Board Support
PC Board
PC Board Support Fixture
Figure 2
Rev H
2
of 4
408-8501
5. MAINTENANCE AND INSPECTION
5.1. Daily Maintenance
It is recommended that each operator be made aware of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and other contaminants with a clean, soft brush, or lint-free cloth. DO NOT
use objects that could damage the tool or any of its components.
2. Ensure that the screws are in place and secured.
3. When the tool is not in use, store it in a clean, dry area.
5.2. Inspection
Each seating tool is assembled and inspected before shipment. It is recommended that the tool be inspected
using Figure 3 immediately upon arrival to assure that it has not been damaged during shipment.
Regular inspections should be performed by quality control personnel. A record of scheduled inspections
should remain with the tool or be supplied to personnel responsible for the tool. The inspection frequency
should be based on the amount of use, working conditions, operator training and skill, and established
company standards.
6. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 3. A complete inventory should be stocked and controlled to
prevent lost time when replacement of parts is necessary. Order replacement parts through your local TE
Connectivity Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to
717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
7. REVISION SUMMARY
Revisions to this instruction sheet include:
Added new part numbers and related information to tables in Figure 3
This is a new power IC from TI. I am not good at English and I did not understand the data sheet. For example, if the output is 3.6V, is the ++ in the table a recommended choice? The inductor is 2.2uH...
[i=s]This post was last edited by Jacktang on 2020-5-4 08:35[/i]Data SheetTMS320C6745, TMS320C6747 Fixed- and Floating-Point Digital Signal Processor 数据表(英文內容)|
Online data sheetErrataTMS320C6747 Fixe...
[i=s] This post was last edited by 享受de成长 on 2015-4-24 10:29 [/i] I was doing an experiment with a Bluetooth module recently and found that when I ran the Bluetooth startup script, I got the following...
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_unsigned .all;
entity liushuideng is
port(clk:in std_logic;
led:out std_logic_vector(7 downto 0));
end entity;
architecture bhv of liushui...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
introduction
LEDs continue to gain popularity in automotive applications, thanks to their long lifespan and the flexibility they offer for body styling and interior design. Some may be surpris...[Details]
store
To prevent moisture, LEDs should be stored in a dry and ventilated environment with a storage temperature of -40°C to +100°C and a relative humidity below 85%.
The LED should be use...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
introduction
Caller ID delivery (CID) is a service provided to the user's phone. The method is that the originating switch transmits the caller number and other information to the terminal swi...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
In the 1980s, breakthroughs were made in the design and production of small, low-power quartz metal halide lamps with precise dimensions. At the same time, with the acceleration of people's lives a...[Details]
In the process of instrument application, there are many types of influencing factors of online gas analyzers and the changes are more complex. It is difficult to effectively control these influenc...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
