EEWORLDEEWORLDEEWORLD

Part Number

Search

PLL620-2XOCR

Description
Low Phase Noise VCXO (for 100-200MHz Fund Xtal)
File Size211KB,6 Pages
ManufacturerPLL (PhaseLink Corporation)
Download Datasheet View All

PLL620-2XOCR Overview

Low Phase Noise VCXO (for 100-200MHz Fund Xtal)

PLL620-28/-29
Low Phase Noise VCXO (for 100-200MHz Fund Xtal)
FEATURES
100MHz to 200MHz Fundamental Mode Crystal.
Output range: 100 – 200MHz (no PLL).
Low Injection Power for crystal 50uW.
Sub 0.5pS RMS phase jitter ( 12kHz to 20MHz ).
PECL (PLL620-28) or LVDS output (PLL620-29).
Supports 2.5V or 3.3V-Power Supply.
Available in 16-Pin TSSOP.
PIN CONFIGURATION
(Top View)
DESCRIPTION
The PLL620-28/-29 family of XO ICs is specifically
designed to work with high frequency fundamental
and third overtone crystals. They achieve very low
current into the crystal, resulting in better stability.
Their very low jitter makes them ideal for the most
demanding timing requirements.
BLOCK DIAGRAM
OE
Q
XIN
XOUT
Oscillator
Amplifier
Q
OUTPUT ENABLE LOGICAL LEVELS
Part #
PLL620-28
OE
0 (Default)
1
0
1 (Default)
State
Output enabled
Tri-state
Tri-state
Output enabled
PLL620-28/-29
PLL620-29
OE input: Logical states defined by PECL levels for PLL620-28
Logical states defined by CMOS levels for PLL620-29
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 07/08/05 Page 1
Wince serial communication
I wrote a serial communication tool. When I debugged it with VS2005, the received data was correct. But when it ran normally, the received data was wrong. For example: Source data: 1234567 1234567 ......
lhzisname Embedded System
Timing Analysis and Timing Constraints
Timing Analysis and Timing Constraints...
tonytong MCU
How to use E-coins?
How to use E coins? Can I buy things? Are you referring to development boards? How to operate?...
cl17726 Suggestions & Announcements
After the stepper motor is powered on according to the timing, it just shakes left and right and does not rotate. I would like some guidance.
The stepper motor runs in full step mode, and the delay has been tried in the range of 5ms--50ms. Only the sound changes, but the operation does not change. I have been wondering if there is a problem...
Bjdj Motor Drive Control(Motor Control)
DA double buffering method
[i=s]This post was last edited by paulhyde on 2014-9-15 09:43[/i] How should I program the DA double buffering method? Why can't I transfer data?...
liu5013 Electronics Design Contest
There was an error when installing MySQL, please help me solve it!
When I was installing MySQL, an error occurred: %pre(MySQL-server-community-5.1.60-1.rhel4) scriptlet failed, exit status 1 error: install: %pre scriptlet failed (2), skipping MySQL-server-community-5...
lw209 Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2168  1726  2027  903  2091  44  35  41  19  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号