chips. They provide phase noise performance as low
as –125dBc at 10kHz offset (at 155MHz), by multi-
plying the input crystal frequency up to 32x. The
wide pull range (+/- 200 ppm) and very low jitter
make them ideal for a wide range of applications,
including SONET/SDH and FEC. They accept fun-
damental parallel resonant mode crystals from 12 to
25MHz.
XOUT
SEL3^
SEL2^
OE
13
14
15
16
12
11
10
SEL1^
9
DESCRIPTION
XIN
SEL0^ / VDD*
VDD / GND*
P502-3x
1
2
3
4
PLL 502-3x
GND
GND
8
7
6
5
GND
CLKC
VDD
CLKT
VCON
BLOCK DIAGRAM
SEL
OE
Vin
X+
X-
Oscillator
Amplifier
w/
integrated
varicaps
PLL
(Phase
Locked
Loop)
^:
*:
Internal pull-up
On 3x3 package, PLL502-35/-38 do not have SEL0 available: Pin
10 is VDD, pin 11 is GND. However, PLL502-37/-39 have SEL0
(pin 10), and pin11 is VDD. See pin assignment table for details.
OUTPUT ENABLE LOGICAL LEVELS
Part #
PLL502-38
PLL502-35
PLL502-37
PLL502-39
OE
0 (Default)
1
0
1 (Default)
Tri-state
Tri-state
GND
State
Output enabled
Q
Q
Output enabled
PLL by-pass
PLL502-3x
OE input: Logical states defined by PECL levels for PLL502-38
Logical states defined by CMOS levels for PLL502-37/-39
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 01/19/06 Page 1
PLL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise IC’s
FREQUENCY SELECTION TABLE
SEL3
0
0
0
1
1
1
1
1
1
1
SEL2
0
1
1
0
0
0
1
1
1
1
SEL1
1
1
1
0
1
1
0
0
1
1
SEL0
1
0
1
1
0
1
0
1
0
1
Selected Multiplier
Fin x 32
Fin / 8
Fin x 2
Fin / 2
Fin / 16
Fin x 4
Fin / 4
Fin x 8
Fin x 16
No multiplication
Note:
SEL0 is not available (always “1”) for PLL502-35 and PLL502-38 in 3x3mm package
PIN DESCRIPTIONS PLL502-35 and PLL502-38 (see next page of PLL502-37/-39)
Name
XIN
XOUT
OE
VCON
GND
CLKT
CLKC
SEL0
SEL1
SEL2
SEL3
VDD
TSSOP
Pin number
2
3
6
7
8,9,10,14
11
13
16
15
5
4
1, 12
3x3mm QFN
Pin number
12
13
16
1
2,3,4,8,11
5
7
Not available
9
15
14
6,10
Type
I
I
I
I
P
O
O
I
I
I
I
P
Description
Crystal input. See Crystal Specification on page 4.
Crystal output. See Crystal Specification on page 4.
Output enable pin (see OE logic state table on page 1).
Voltage Control input.
Ground.
True output PECL
Complementary output PECL.
Multiplier selector pins. These pins have an internal pull-up
that will default SEL to ‘1’ when not connected to GND.
+3.3V power supply.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 01/19/06 Page 2
PLL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise IC’s
PIN DESCRIPTIONS PLL502-37/-39 (see previous page of PLL502-35/-38)
Name
XIN
XOUT
OE
VCON
GND
CLKT
CLKC
SEL0
SEL1
SEL2
SEL3
VDD
TSSOP
Pin number
2
3
6
7
8,9,10,14
11
13
16
15
5
4
1, 12
3x3mm QFN
Pin number
12
13
16
1
2,3,4,8
5
7
10
9
15
14
6,11
Type
I
I
I
I
P
O
O
I
I
I
I
P
Description
Crystal input. See Crystal Specification on page 4.
Crystal output. See Crystal Specification on page 4.
Output enable pin (see OE logic state table on page 1).
Voltage Control input.
Ground.
True output LVDS (PLL502-39)
(N/C for PLL502-37)
Complementary output LVDS (PLL502-39)
(CMOS out for PLL502-37).
Multiplier selector pins. These pins have an internal pull-up
that will default SEL to ‘1’ when not connected to GND.
+3.3V power supply.
ELECTRICAL SPECIFICATIONS
1. Absolute Maximum Ratings
PARAMETERS
Supply Voltage
Input Voltage, dc
Output Voltage, dc
Storage Temperature
Ambient Operating Temperature*
Junction Temperature
Lead Temperature (soldering, 10s)
ESD Protection, Human Body Model
SYMBOL
V
DD
V
I
V
O
T
S
T
A
T
J
MIN.
-0.5
-0.5
-65
-40
MAX.
4.6
V
DD
+0.5
V
DD
+0.5
150
85
125
260
2
UNITS
V
V
V
°C
°C
°C
°C
kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the
device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other con-
ditions above the operational limits noted in this specification is not implied.
*
Note:
Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 01/19/06 Page 3
PLL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise IC’s
2. Crystal Specifications
PARAMETERS
Crystal Resonator Frequency
Crystal Loading Rating
Crystal Pullability
Recommended ESR
SYMBOL
F
XIN
C
L (xtal)
C
0
/C
1 (xtal)
R
E
CONDITIONS
Parallel Fundamental Mode
At VCON = 1.65V
AT cut
AT cut
MIN.
12
TYP.
9.5
MAX.
25
250
30
UNITS
MHz
pF
-
Ω
Note:
Crystal Loading rating: 9.5pF is the loading the crystal sees from the VCXO chip at VCON = 1.65V. It is assumed that the crystal will be at nomi-
nal frequency at this load. If the crystal requires more load to be at nominal frequency, the additional load must be added externally. This however may
reduce the pull range.
3. Voltage Control Crystal Oscillator
PARAMETERS
VCXO Stabilization Time *
VCXO Tuning Range
CLK output pullability
VCXO Tuning Characteristic
Pull range linearity
VCON pin input impedance
VCON modulation BW
SYMBOL
T
VCXOSTB
CONDITIONS
From power valid
F
XIN
= 12 – 25MHz;
XTAL C
0
/C
1
< 250
0V
≤
VCON
≤
3.3V
VCON=1.65V,
±1.65V
MIN.
TYP.
MAX.
10
UNITS
ms
ppm
ppm
ppm/V
%
kΩ
kHz
500
±200
150
10
2000
25
0V
≤
VCON
≤
3.3V, -3dB
Note:
Parameters denoted with an asterisk (*) represent nominal characterization data and are not production tested to any specific limits.
4. General Electrical Specifications
PARAMETERS
Supply Current,
Dynamic (with
Loaded Outputs)
Operating Voltage
Output Clock
Duty Cycle
Short Circuit
Current
SYMBOL
I
DD
V
DD
CONDITIONS
PECL/LVDS/CMOS
Fout<24MHz
24MHz<Fout<96MHz
96MHz<Fout<800MHz
MIN.
TYP.
MAX.
60/28/15
65/45/30
100/80/40
3.63
55
55
55
UNITS
mA
V
%
mA
2.97
@ 50% V
DD
(CMOS)
@ 1.25V (LVDS)
@
V
DD
– 1.3V (PECL)
45
45
45
50
50
50
±50
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 01/19/06 Page 4
PLL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise IC’s
5. Jitter Specifications
PARAMETERS
CONDITIONS
With capacitive decoupling be-
tween VDD and GND.
Over 10,000 cycles.
FREQUENCY
19.44MHz
77.76MHz
155.52MHz
622.08MHz
19.44MHz
77.76MHz
155.52MHz
622.08MHz
155.52MHz
622.08MHz
MIN.
TYP.
2.2
4.5
4.5
5.0
17
25
27
35
2.5
2.5
MAX.
UNITS
Period jitter RMS
ps
Period jitter Peak-to-
Peak
1
With capacitive decoupling be-
tween VDD and GND.
Over 10,000 cycles.
Integrated 12 kHz to 20 MHz
ps
Integrated jitter RMS
2
4
4
ps
6. Phase Noise Specifications
PARAMETERS
Phase Noise relative
to carrier
(typical)
FREQUENCY
19.44MHz
77.76MHz
155.52MHz
622.08MHz
@10Hz
-80
-72
-65
-55
@100Hz
-108
-103
-95
-85
@1kHz
-132
-122
-120
-109
@10kHz
-142
-130
-125
-115
@100kHz
-150
-125
-121
-110
UNITS
dBc/Hz
Note: Phase Noise measured at VCON = 0V
7. CMOS Electrical Characteristics
PARAMETERS
Output drive current
Output Clock Rise/Fall Time
SYMBOL
I
OH
I
OL
CONDITIONS
V
OH
= V
DD
-0.4V, V
DD
=3.3V
V
OL
= 0.4V, V
DD
= 3.3V
0.3V ~ 3.0V with 15 pF load
MIN.
10
10
TYP.
MAX.
UNITS
mA
mA
ns
2.4
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
How does the Wince interface respond to the touch pen swipe operation? How to make a dynamic interface effect like the iPhone/M8 screen swipe effect!...
I'm currently working on a project that uses the heterogeneous dual-core Vybrid VF6. I don't really understand it, so I'd like an expert to share some information or experience....
Source: http://www.ourdev.cn/bbs/bbs_content.jsp?bbs_sn=657257&bbs_page_no=1&bbs_id=9999 Finally it works! Haha: I'll share it with you! You don't need to change anything in it, just change the macro ...
When using stm32f103vc 100pin to do a project, I encountered a problem.We want to use 103vc's fmsc to hang 5 peripherals. Four of the addresses of these 5 peripherals only need 2 address lines, and th...
Ultrasound systems can produce images of internal organs and structures, map blood flow and tissue movement, and provide highly accurate blood flow velocity information by transmitting acoustic energy...
I have a s3c2410 (arm920t, flash: 16m, sdrom: 64m) development board. Now I use PPCBOOT2.0.0 to boot LINUX and everything is normal. I want to use this development board to run vxworks. How should I d...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
