Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
[i=s] This post was last edited by paulhyde on 2014-9-15 03:13 [/i] When I increase the input voltage during TINA simulation, I keep getting the error message: No operating point found. Why is this ha...
Now using S3C2440, it is still a bit difficult to understand OEMAddressTable and config.bib together. The path of OEMAddressTable (pre-CE 5.0) is generally: %WINCEROOT%\PLATFORM\\KERNEL\HAL\ARM in the...
Hello everyone! I want to use VC to implement a serial port forwarding function, that is, if there is data coming from serial port 1, it will be forwarded to serial port 2, and if there is data coming...
Development board model: Gravity HUSKYLENS AI camera (5 sets in total)
From: DFRobot
Market price: 379 yuanHuskyLens is an easy-to-use AI vision sensor that uses the new generation AI chip Kendryte K2...
Hi guys, I need help. I am using S5PV210 to do TVout (CVBS signal output) and I am using Linux operating system. I have given the image to GPR0 and can see the image on the monitor now, but the color ...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
