Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
I am a novice in MSP430. After reading the book about MSP430, I want to practice it. But I don't have a development board. If any seniors don't use the development board, can you lend it to me? I will...
For example, if the duty cycle is 20%, the PWM output pin cannot use the timer, so I use the interrupt timing to achieve the output, and the timing time sets the pin high or low. Now I want to ask: ho...
There were two posts on the forum. The first one was a strange circuit that used 24V to divide into 16V and 8V, and then generated 10.4, 9.3, 3.3 from 16V, and -7V from 8V. The 9.3V generated by that ...
Why can't I output a square wave using this program? I can't detect a square wave output at the P0.0 pin using an oscilloscope, nor can I detect a square wave output at other P0 ports, only a DC volta...
Compilation environment: AVR studioAfter the program is basically modified, there is no error or warning in AVR studio, but when it is downloaded to the microcontroller, there is no display on the scr...
[p=28, 2, left][color=rgb(51, 51, 51)][backcolor=rgb(247, 247, 247)][font=宋体]1. The base must be connected in series with a resistor to protect the base and the CPU's IO port. [/font][/backcolor][/col...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
