5.0 mm x 3.2 mm Package Pinout ............................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
Device Configurations and Pin-outs ............................................................................................................................................. 9
Pin-out Top Views................................................................................................................................................................. 9
Test Circuit Diagrams for LVCMOS and Clipped Sinewave Outputs ......................................................................................... 10
Frequency Stability ............................................................................................................................................................. 16
Output Frequency and Format............................................................................................................................................ 16
Output Frequency Tuning ................................................................................................................................................... 16
Pin 1 Configuration (OE, VC, or NC) .................................................................................................................................. 17
Control Voltage Bandwidth ................................................................................................................................................. 20
Pull Range and Average Pull Range .................................................................................................................................. 22
Output Frequency ............................................................................................................................................................... 23
2
I C Control Registers .......................................................................................................................................................... 25
Serial Interface Configuration Description .......................................................................................................................... 28
Serial Signal Format ........................................................................................................................................................... 28
Parallel Signal Format ........................................................................................................................................................ 29
Parallel Data Format ........................................................................................................................................................... 29
2
I C Timing Specification ...................................................................................................................................................... 31
2
I C Device Address Modes ................................................................................................................................................. 32
Schematic Example ............................................................................................................................................................ 33
Dimensions and Patterns ........................................................................................................................................................... 34
Additional Information ................................................................................................................................................................ 36
Revision History ......................................................................................................................................................................... 37
Rev 1.05
Page 3 of 38
www.sitime.com
SiT5156
1 MHz to 60 MHz, ±0.5 to ±2.5 ppm, Elite Platform™ Super-TCXO
Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and 3.3V Vdd.
Table 1. Output Characteristics
Parameters
Nominal Output Frequency Range
Operating Temperature Range
Symbol
F_nom
T_use
Min.
1
-20
-40
-40
Frequency Stability over
Temperature
Initial Tolerance
Supply Voltage Sensitivity
F_stab
–
–
–
F_init
F_Vdd
–
–
–
–
Output Load Sensitivity
F_load
–
–
–
Frequency vs. Temperature Slope
ΔF/ΔT
–
–
–
Dynamic Frequency Change during
Temperature Ramp
One-Year Aging
20-Year Aging
F_dynamic
–
–
–
F_1y
F_20y
–
–
Typ.
–
–
–
–
–
–
–
–
±7.10
±11.83
±28.40
±0.81
±1.35
±3.24
±15
±25
±60
±0.13
±0.21
±0.50
±1
±2
Max.
60
+70
+85
+105
±0.5
±1.0
±2.5
±1
±16.25
±32.50
±65.0
±2.75
±5.50
±11.00
±25
±50
±100
±0.21
±0.42
±0.83
–
–
Unit
MHz
°C
°C
°C
ppm
ppm
ppm
ppm
ppb
ppb
ppb
ppb
ppb
ppb
ppb/°C
ppb/°C
ppb/°C
ppb/s
ppb/s
ppb/s
ppm
ppm
Initial frequency at 25°C at 48 hours after 2 reflows
1. hw_config.c file: modify USB clock related configuration and USB enable pin output mode (refer to Joystick); 2. usb_desc.c file: modify PID to 0x5721 (or others, 0x5720 seems to be built-in ST-LINK...
The control circuit below is shown in the figure. The live wire first passes through the thyristor circuit zero-crossing trigger and then reaches the relay circuit.Every 15 waveforms of the heating po...
I collected a Ycbcr image from the camera, but I didn't know how to display it, so I converted it to RGB. Now that it has been converted to an RGB image, I want to see if it is collected correctly, so...
We are looking for people with experience in LED control card (synchronous or asynchronous card) projects. We will provide preferential treatment. Full-time or part-time is acceptable. Full-time will ...
I'm a newbie and now I'm facing a problem. I'm using SPI to send 64-bit data continuously. After a long time, there are always interruptions in the middle. I'd like some help from an expert!...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
Key Points
1. Now, in addition to high-end smartphones and tablets, users also expect to use touch screens in other applications, and they are gradually appearing in cars and instruments.
...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
