5.0 mm x 3.2 mm Package Pinout ............................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
Device Configurations and Pin-outs ............................................................................................................................................. 9
Pin-out Top Views................................................................................................................................................................. 9
Test Circuit Diagrams for LVCMOS and Clipped Sinewave Outputs ......................................................................................... 10
Frequency Stability ............................................................................................................................................................. 16
Output Frequency and Format............................................................................................................................................ 16
Output Frequency Tuning ................................................................................................................................................... 16
Pin 1 Configuration (OE, VC, or NC) .................................................................................................................................. 17
Control Voltage Bandwidth ................................................................................................................................................. 20
Pull Range and Average Pull Range .................................................................................................................................. 22
Output Frequency ............................................................................................................................................................... 23
2
I C Control Registers .......................................................................................................................................................... 25
Serial Interface Configuration Description .......................................................................................................................... 28
Serial Signal Format ........................................................................................................................................................... 28
Parallel Signal Format ........................................................................................................................................................ 29
Parallel Data Format ........................................................................................................................................................... 29
2
I C Timing Specification ...................................................................................................................................................... 31
2
I C Device Address Modes ................................................................................................................................................. 32
Schematic Example ............................................................................................................................................................ 33
Dimensions and Patterns ........................................................................................................................................................... 34
Additional Information ................................................................................................................................................................ 36
Revision History ......................................................................................................................................................................... 37
Rev 1.05
Page 3 of 38
www.sitime.com
SiT5156
1 MHz to 60 MHz, ±0.5 to ±2.5 ppm, Elite Platform™ Super-TCXO
Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and 3.3V Vdd.
Table 1. Output Characteristics
Parameters
Nominal Output Frequency Range
Operating Temperature Range
Symbol
F_nom
T_use
Min.
1
-20
-40
-40
Frequency Stability over
Temperature
Initial Tolerance
Supply Voltage Sensitivity
F_stab
–
–
–
F_init
F_Vdd
–
–
–
–
Output Load Sensitivity
F_load
–
–
–
Frequency vs. Temperature Slope
ΔF/ΔT
–
–
–
Dynamic Frequency Change during
Temperature Ramp
One-Year Aging
20-Year Aging
F_dynamic
–
–
–
F_1y
F_20y
–
–
Typ.
–
–
–
–
–
–
–
–
±7.10
±11.83
±28.40
±0.81
±1.35
±3.24
±15
±25
±60
±0.13
±0.21
±0.50
±1
±2
Max.
60
+70
+85
+105
±0.5
±1.0
±2.5
±1
±16.25
±32.50
±65.0
±2.75
±5.50
±11.00
±25
±50
±100
±0.21
±0.42
±0.83
–
–
Unit
MHz
°C
°C
°C
ppm
ppm
ppm
ppm
ppb
ppb
ppb
ppb
ppb
ppb
ppb/°C
ppb/°C
ppb/°C
ppb/s
ppb/s
ppb/s
ppm
ppm
Initial frequency at 25°C at 48 hours after 2 reflows
The event is over, and looking back at the road I have walked, I feel very relieved. I first entered this DIY event in early May. At that time, I saw everyone on EEWORLD discussing the "DIY event plan...
Be very careful when using lis25ba. I didn't pay attention yesterday and used a little too much force, which caused the solder pad of the pin header to fall off, and a wire flew off....
Is there any sensor that can measure the distance between the measuring point and the water surface? Or can I use something else to measure without a sensor? Or how to measure the volume of a containe...
The original folders on the mobile phone memory card have all changed to the suffix ink format. They cannot be opened on the mobile phone and can only be opened on the computer. What is the reason?...
My board is 9b92 and I use ulink2 + keil 4.10. There is no problem with program compilation and ulink, but it fails when downloading. This is the relevant settings page. Please help me take a look. I ...
When laying differential lines, the lengths of the two lines should be as equal as possible, the distance between the two lines should be as close as possible, and the two lines should be kept paralle...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
Analysis of the three core aspects of digital TV transmission standards
According to the differences in regionality, transmission method and modulation method, the transmission method needs to...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
introduction
When it comes to the production of mobile phone lithium-ion batteries, the first thing that comes to mind is Japan's industrialized mechanical assembly line, NOKIO, MOTOLROLA's st...[Details]
Don’t just look at the power when choosing a power supply
We know that a power supply with a low rated power can hardly meet the power supply needs of the system, which may cause frequent free...[Details]
1. Introduction
Modern modular machine tools are equipped with a large number of electronic devices to meet the requirements of processing accuracy, processing speed, etc. If the conventional ...[Details]
Microcontrollers are something that many people want to learn about and are concerned about. In most websites, the hardware requirements are generally as follows:
1. You need a computer, prefer...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
