The FN 3311 HV/FN 3310 HV poduct series of standard
EMC/EMI filters are based on Schaffner’s many years of
expertise in filter design for all types of converter and
inverter applications. Installed between the PV
inverter and the power grid, the FN 3311HV and FN
3310HV AC filters are used to influence positively the
conducted emissions on the grid side to help to
comply with the required emission standards.
Features and benefits
The FN 3311 HV/FN 3310 HV series are the most
compact dedicated high current AC filters, not only
suitable for PV applications, but being an optimum fit
with most modern PV inverter topologies. In addition
the filters can be configured in a very flexible way to
fulfil custom specific application requirements.
All FN 3311 HV/FN 3310 HV come in unsymmetrical
housings, which help to prevent inverse installation
and wrong electrical connection. The AC filters FN
3311 HV/FN 3310 HV are key to meet the stringent
international standards for electromagnetic
compatibility and help to ensure a reliable and fault-
free operation of the entire PV system.
Technical specifications
Maximum continuous operating voltage
Operating frequency
Rated currents
High potential test voltage
3x 760/440 VAC for FN 3311 HV
3x 760 VAC for FN 3310 HV and FN 3311 HVIT
DC to 60 Hz
250 to 2300 A @ 50°C
P –> E 3.0 kVAC for 2 s
(FN 3310 HV/FN 3311 HVIT 3.35 kVAC for 2 s)
P –> P 3.45 kVDC for 2 s
IP 00
4x rated current at switch on, max. 8 sec
1.5x rated current for 1 minute, once per hour
-40°C to +100°C
40/100/21 acc. to IEC 60068-1
Ni plated cu bars/Metal
UL 94V-0
UL 1283, CSA 22.2 No. 8, IEC/EN 60939, EN 60721-3
Typical applications
The FN 3311 HV/FN 3310 HV series are primarily
designed for all kind of power line connected
converter and inverter applications between 250 and
2'300 A. However, they are optimised for PV inverter
and can potentially also be applied for general
purpose motor drives applications.
Protection category
Overload capability
Temperature range (operation and storage)
Climatic category
Terminals/Housing
Flammability corresponding to
Design corresponding to
Typical electrical schematic FN 3311 HV
*
*
- FN 3311 HVIT series without resistor to PE
- FN 3310 HV series without resistor and capacitor
to PE
2
EMC/EMI Products
Schaffner Group
Datasheets
2016
Filter selection table
Filters */**
Rated current
@ 50°C
Typical inverter
AC power rating***
Leakage current****
@ 760 VAC/50 Hz
Power losss
@ 25°C/DC
Weight
[A]
FN 3311 HV with Cy caps
FN 3311 HV-250-99-C18-R55
FN 3311 HV-400-99-C18-R55
FN 3311 HV-600-99-C18-R55
FN 3311 HV-1000-99-C18-R55
FN 3311 HV-1500-99-C18-R55
FN 3311 HV-2300-99-C18-R55
FN 3311 HVIT with Cy caps
FN 3311 HVIT-250-99-C18-R5
FN 3311 HVIT-400-99-C18-R5
FN 3311 HVIT-600-99-C18-R5
FN 3311 HVIT-1000-99-C18-R5
FN 3311 HVIT-1500-99-C18-R5
FN 3311 HVIT-2300-99-C18-R5
250
400
600
1000
1500
2300
[kVA]
[mA]
[W]
[kg]
140
220
330
550
830
1250
0.09
0.09
0.09
0.09
0.09
0.09
18
30
33
70
133
201
2.7
3.3
4.5
6.1
11.0
18.0
FN 3310 without Cy caps
FN 3310 HV-250-99-R5
FN 3310 HV-400-99-R5
FN 3310 HV-600-99-R5
FN 3310 HV1000-99-R5
FN 3310 HV-1500-99-R5
FN 3310 HV-2300-99-R5
250
400
600
1000
1500
2300
140
220
330
550
830
1250
18
30
33
70
133
201
2.7
3.3
4.5
6.1
11.0
18.0
* Filters with higher current ratings available upon request.
** Filters with reduced Cy capacitance to ground for high asymmetrical currents and higher voltages available upon request.
*** Calculated at rated current, 690 VAC and cos phi = 0.8. The exact value depends upon the efficiency of the drive, the motor and the entire application.£
**** Leakage current according IEC 60939-1
Typical filter attenuation curves
Per CISPR 17; A=50 Ω/50 Ω sym; B=50 Ω/50 Ω asym
FN 3311 HV-250...2300-99-C18-R5
and
FN 3311 HVIT-250...2300-99-C18-R55
FN 3310 HV-250...2300-99-R5
Typical block schematic
1
PV modules
2
Schaffner DC filter FN 22xx
3
Central Inverter
4
Schaffner magnetic components
5
Schaffner AC EMC/EMI filter FN 3xxx
Important note: depending on the grounding scheme of the solar power system, including the solar panel and the grid side transformer, the appropriate DC- and AC
EMC/EMI filter version need to be selected. For support, please contact your local Schaffner sales office or partner.
3
EMC/EMI Products
Schaffner Group
Datasheets
2016
Mechnical data
250 to 2'300 A types
Busbar connections
250 to 1'000 A types
1'500 A types
2'300 A types
Note:
all FN 3311 and FN 3310 provide unsymmetrical mounting hole patterns to prevent inverse filter installation in the field.
Dimensions of FN 3311 HV and FN 3310 HV series
(the FN 3311 HVIT versions have the same dimensions as the FN 3311 HV)
250 A
A
B
C
D
E
F1
F2
G
H
J
K
L
O
P
S
T
U
V
W
X
Y
Z
41
20
3
10
32.5
Ø9
46
25
4
12.5
37.5
Ø11
50
25
8
12.5
37.5
Ø11
53
40
8
20
57.5
Ø13.5
170
267
140
235
195
227
232
Ø7 (6x)
1.5
M6 (2x)
200 (+/- 1)
215
24.5
49 (+/- 0.5)
400 A
175
280
140
250
205
240
245
Ø9 (6x)
2
M8 (2x)
210 (+/- 1)
230
27
54 (+/- 0.5)
600 A
190
290
140
265
220
250
255
Ø9 (6x)
2.5
M8 (2x)
225 (+/- 1)
245
29.5
59 (+/- 0.5)
1'000 A
190
290
140
305
220
250
255
Ø9 (6x)
2.5
M8 (2x)
225 (+/- 1)
245
29.5
59 (+/- 0.5)
1'500 A
195
310
150
360
240
270
275
Ø11 (6x)
2.5
M10 (2x)
241 (+/- 1)
265
34.8
69.5 (+/- 0.5)
26
26
58
60
10
17
82.5
Ø13.5
2'300 A
220
320
165
410
265
275
280
Ø11 (6x)
2.5
M10 (2x)
266 (+/- 1)
290
40
80 (+/- 0.5)
40
35
60.5
70
15
20
95
Ø13.5
All dimensions in mm; 1 inch = 25.4 mm
Tolerances according: ISO 2768-m/EN 22768-m, if not stated otherwise
Please see the brochure "Basics in EMC and Power Quality" on our website www.schaffner.com to find more details on filter connectors.
[i=s]This post was last edited by lkl0305 on 2016-5-20 09:58[/i] [align=center][b][size=5]Low-power thumb board[/size][/b][/align][align=center][b][size=5]——NUCLEO-L011K4 review[/size][/b][/align][ali...
As the title says, I have been trying for many days but have not found a better solution. I want to consider the underlying driver, but I don't know how to do it and I don't have any driver foundation...
These are some of my papers on Xilinx FPGA. I upload them to share with you! Please support me!
I will upload them in batches to facilitate everyone's selective communication and downloading![[i]This ...
The output voltage range is required to be 0V~9.9V, the ripple is not greater than 10mV, the step is 0.1v, the output current is greater than 500mA, the output initial value can be preset, and the out...
Related articles :
【GD32L233C-START Review】03 LED Operation and General Timing Function
Preface
We continue to understand the functions of the MCU based on the resources that come with the board. This...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
introduction
When it comes to the production of mobile phone lithium-ion batteries, the first thing that comes to mind is Japan's industrialized mechanical assembly line, NOKIO, MOTOLROLA's st...[Details]
The power consumption of a switching power supply includes fixed losses caused by parasitic resistances such as semiconductor switches, magnetic components, and wiring, as well as switching losses ...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
