packages with exceptional frequency stability, and jitter
performance over temperature. The single-output
DSC60xxB MEMS oscillators are excellent choices for
use as clock references in small, battery-powered
devices such as wearable and Internet of Things (IoT)
devices in which small size, low power consumption,
and long-term reliability are paramount. The
Automotive Grade AEC-Q100 qualified option is
available for this device.
The DSC60xxB family is available in ultra-small
1.6 mm x 1.2 mm, 2.0 mm x 1.6 mm and 2.5 mm x
2.0 mm packages. These packages are “drop-in”
replacements for standard 4-pin CMOS quartz crystal
oscillators.
Package Types
DSC60
XX
B
2.5 mm x 2.0 mm LGA
2.0 mm x 1.6 mm LGA
1.6 mm x 1.2 mm LGA
(Top View)
Applications
• Low Power/Portable Applications: IoT,
Embedded/Smart Devices
• Consumer: Home Healthcare, Fitness Devices,
Home Automation
• Automotive: Rear View/Surround View Cameras,
Infotainment System (Please refer to DSA60xx
Family)
• Industrial: Building/Factory Automation,
Surveillance Camera
OE/STDBY/FS
1
4
VDD
GND
2
3
OUT
2019 Microchip Technology Inc.
DS20006133A-page 1
DSC60XXB
Block Diagram
DSC60xxB
DIGITAL
CONTROL
OE/STBY/FS
PIN 1
SUPPLY
REGULATION
VDD
PIN 4
MEMS
RESONATOR
TEMP SENSOR
CONTROL &
COMPENSATION
PLL
VCO
OUTPUT
DIVIDER
DRIVER
OUTPUT
PIN 3
GND
PIN 2
DS20006133A-page 2
2019 Microchip Technology Inc.
DSC60XXB
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
Supply Voltage .......................................................................................................................................... –0.3V to +4.0V
Input Voltage (V
IN
) ..............................................................................................................................–0.3V to V
I use the st usb library, but I don't know how to detect the completion of the transmission? Now I usewhile(GetEPTxStatus(ENDP1) != EP_TX_NAK);but in some cases this judgment does not work. Now I can ...
Altera Quartus II 14.1 uses DSE to optimize Quartus II design : https://training.eeworld.com.cn/course/2050Watch this demonstration to learn how you can use DSE to optimize your Quartus II design for ...
[font=楷体, 楷体_GB2312][size=4]I am using the Wildfire M3 development board to do an RFID experiment. The experimental phenomenon is somewhat different from that in the manual. [/size][/font] This is the...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
