Type 225P
Vishay Sprague
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
FEATURES
•
Utilizes minimum area where printed wiring
board space is most important
•
Wound from PETP polyester film and thin gauge
RoHS
foil under carefully controlled atmospheric
COMPLIANT
conditions
•
Protected against moisture by a conformal coating of
epoxy
•
Specifically designed for printed wiring board applications
•
Widely used in computers, instrumentation and
telecommunications equipment
•
100 VDC through 600 VDC, may be operated up to
+ 125 °C with proper dearting
PERFORMANCE CHARACTERISTICS
Operating Temperature:
- 55 °C to + 85 °C
To + 105 °C when working voltage is reduced to 70 % of
+ 85 °C rating; to + 125 °C when working voltage is reduced
to 50 % of 85 °C rating
Insulation Resistance:
After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25 °C: 100 000 Megohm for C
≤
0.25 Microfarads
25000 Megohm - Microfarads for C > 0.25 Microfarads
At + 85 °C: 10 000 Megohm for C
≤
0.15 Microfarads
1500 Megohm - Microfarads for C > 0.15 Microfarads
At + 105 °C: 1500 Megohm for C
≤
0.17 Microfarads
250 Megohm - Microfarads for C > 0.17 Microfarads
At + 125 °C: 200 Megohm for C
≤
0.13 Microfarads
25 Megohm - Microfarads for C > 0.13 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %
Dielectric Withstanding Voltage:
Capacitors shall withstand a DC potential of 250 % of rated
voltage applied between terminals for not more than 5
seconds. The test voltage must be applied and discharged
through a resistor of 1 ohm per volt.
Humidity Test:
Condition capacitors with no voltage applied for 72 hours at
95 % relative humidity and + 75 °C. Remove capacitors from
humidity chamber, wipe surface dry of moisture and dry in
circulating air for 4 hours. Measure insulation resistance after
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
whichever is less. Minimum product of insulation resistance
and capacitance shall be 5000 Megohm - Microfarads after
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
DIMENSIONS
in inches [millimeters]
L
Max.
0.237
"
[6.020]
Max.
Lead
Length
Lead
Length
L
Max.
0.237
[6.020]
Max.
H
Max.
0.237
[6.020]
Max.
L
Max.
T Max.
Lead
Length
Tinned Copper-Clad Steel
0.032 [0.813] Dia.
(No. 20 AWG)
S
± 0.060 [1.524]
S
± 0.030 [0.762]
S
± 0.030 [0.762]
Terminal A
Terminal B
Terminal D
CASE
CODE
W
X
Y
Document Number: 42016
Revision: 19-Feb-07
L
(Max.)
0.70 [17.78]
0.80 [20.32]
1.25 [31.75]
S
Terminal A and B
0.562 [14.275]
0.613 [15.570]
0.969 [24.613]
Terminal D
0.375 [9.525]
0.375 [9.525]
0.719 [18.263]
www.vishay.com
25
For technical questions, contact: spresale@vishay.com
Type 225P
Vishay Sprague
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
DISSIPATION FACTOR VS.TEMPERATURE
1.5
% DISSIPATION/1000 Hz
CAPACITANCE CHANGE
16
14
12
10
CAPACITANCE CHANGE ENVELOPE
8
FOR 96 % CONFIDENCE LEVEL
6
4
2
0
2
4
6
- 55 - 40 - 25
0
+ 25 + 50 + 75 + 85 + 105 + 125
- 50
+ 100
TEMPERATURE DEG. CENTIGRADE
% CAPACITANCE CHANGE/1000 Hz
1.0
TYPICAL
0.5
0
- 55 - 40 - 25
- 50
0
+ 25 + 50 + 75 + 85 + 105 + 125
+ 100
TEMPERATURE DEG. CENTIGRADE
STANDARD RATINGS*
L
T
100 VDC/70 VAC**
0.001
225P10291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0012
225P12291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0015
225P15291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0018
225P18291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0022
225P22291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0027
225P27291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0033
225P33291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0039
225P39291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0047
225P47291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0056
225P56291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0068
225P68291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0082
225P82291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.01
225P10391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.012
225P12391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.015
225P15391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.018
225P18391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.022
225P22391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.027
225P27391W
0.70 [17.78]
0.37 [9.40]
0.27 [6.86]
0.033
225P33391W
0.70 [17.78]
0.37 [9.40]
0.27 [6.86]
0.039
225P39391W
0.70 [17.78]
0.42 [10.67]
0.30 [7.62]
0.047
225P47391W
0.70 [17.78]
0.42 [10.67]
0.30 [7.62]
0.056
225P56391W
0.70 [17.78]
0.49 [12.45]
0.34 [8.64]
0.068
225P68391W
0.70 [17.78]
0.49 [12.45]
0.34 [8.64]
0.082
225P82391W
0.70 [17.78]
0.55 [13.97]
0.40 [10.16]
0.1
225P10491W
0.70 [17.78]
0.55 [13.97]
0.40 [10.16]
0.12
225P12491X
0.80 [20.32]
0.57 [14.48]
0.37 [9.40]
0.15
225P15491X
0.80 [20.32]
0.62 [15.75]
0.40 [10.16]
0.18
225P18491X
0.80 [20.32]
0.66 [16.76]
0.43 [10.92]
0.22
225P22491X
0.80 [20.32]
0.70 [17.78]
0.46 [11.68]
0.27
225P27491X
0.80 [20.32]
0.74 [18.80]
0.49 [12.45]
0.33
225P33491X
0.80 [20.32]
0.77 [19.56]
0.52 [13.21]
0.39
225P39491X
0.80 [20.32]
0.81 [20.57]
0.55 [13.97]
0.47
225P47491X
0.80 [20.32]
0.86 [21.84]
0.60 [15.24]
0.56
225P56491Y
1.25 [31.75]
0.88 [22.35]
0.55 [13.97]
0.68
225P68491Y
1.25 [31.75]
0.90 [22.86]
0.58 [14.73]
0.82
225P82491Y
1.25 [31.75]
0.94 [23.88]
0.65 [16.51]
1.0
225P10591Y
1.25 [31.75]
0.98 [24.89]
0.72 [18.29]
®
Distribution Network. For complete Part
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague
Number, add letter and number for terminal and lead length. See Ordering Information (Ex: 225P39391WD3).
** 60 Hz rms
www.vishay.com
26
For technical questions, contact: spresale@vishay.com
Document Number: 42016
Revision: 19-Feb-07
µF
± 10
%
TOLERANCE
PART NUMBER
SIZE
H
Type 225P
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
STANDARD RATINGS*
in inches [millimeters]
µF
± 10
%
TOLERANCE
0.001
0.0015
0.0022
0.0033
0.0047
0.0068
0.01
0.015
0.022
0.033
0.047
0.068
0.1
0.1
0.15
0.22
0.33
0.47
0.68
0.001
0.0015
0.0022
0.0033
0.0047
0.0068
0.01
0.015
0.022
0.033
0.047
0.047
0.068
0.1
0.1
0.15
0.22
0.33
0.47
PART NUMBER
225P10292X
225P15292X
225P22292X
225P33292X
225P47292X
225P68292X
225P10392X
225P15392X
225P22392X
225P33392X
225P47392X
225P68392X
225P10492X
225P10492Y
225P15492X
225P22492X
225P33492Y
225P47492Y
225P68492Y
225P10294X
225P15294X
225P22294X
225P33294X
225P47294X
225P68294X
225P10394X
225P15394X
225P22394X
225P33394X
225P47394X
225P47394Y
225P68394X
225P10494X
225P10494Y
225P15494Y
225P22494Y
225P33494Y
225P47494Y
L
200 VDC/140 VAC**
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
1.25 [31.75]
0.80 [20.32]
0.80 [20.32]
1.25 [31.75]
1.25 [31.75]
1.25 [31.75]
400 VDC/200 VAC**
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
1.25 [31.75]
0.80 [20.32]
0.80 [20.32]
1.25 [31.75]
1.25 [31.75]
1.25 [31.75]
1.25 [31.75]
1.25 [31.75]
SIZE
H
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.58 [14.73]
0.58 [14.73]
0.58 [14.73]
0.58 [14.73]
0.61 [15.49]
0.61 [15.49]
0.64 [16.26]
0.71 [18.03]
0.64 [16.26]
0.74 [18.80]
0.77 [19.56]
0.71 [18.03]
0.83 [21.08]
1.14 [28.96]
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.58 [14.73]
0.58 [14.73]
0.58 [14.73]
0.58 [14.73]
0.65 [16.51]
0.65 [16.51]
0.64 [16.26]
0.80 [20.32]
0.84 [21.34]
0.74 [18.80]
0.80 [20.32]
0.89 [22.61]
0.99 [25.15]
1.14 [28.96]
T
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.28 [7.11]
0.28 [7.11]
0.31 [7.87]
0.37 [9.40]
0.31 [7.87]
0.41 [10.41]
0.48 [12.19]
0.41 [10.41]
0.50 [12.70]
0.84 [21.34]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.28 [7.11]
0.28 [7.11]
0.31 [7.87]
0.34 [8.64]
0.41 [10.41]
0.31 [7.87]
0.47 [11.94]
0.52 [13.21]
0.41 [10.41]
0.47 [11.94]
0.56 [14. 22]
0.72 [18.29]
0.84 [21.34]
Vishay Sprague
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague
®
Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
** 60 Hz rms
Document Number: 42016
Revision: 19-Feb-07
For technical questions, contact: spresale@vishay.com
www.vishay.com
27
Type 225P
Vishay Sprague
Polyester Capacitors
Filmite
®
“E”, ORANGE DROP
®
, Radial Lead
STANDARD RATINGS*
in inches [millimeters]
µF
± 10
%
TOLERANCE
0.001
0.0015
0.0022
0.0033
0.0047
0.0068
0.01
0.015
0.018
0.022
0.033
0.039
0.047
0.068
0.1
0.22
PART NUMBER
225P10296X
225P15296X
225P22296X
225P33296X
225P47296X
225P68296X
225P10396X
225P15396X
225P18396X
225P22396X
225P33396X
225P39396X
225P47396X
225P68396Y
225P10496Y
225P22496Y
L
600 VDC/200 VAC**
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
0.80 [20.32]
1.25 [31.75]
1.25 [31.75]
1.25 [31.75]
SIZE
H
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.55 [13.97]
0.58 [14.73]
0.58 [14.73]
0.64 [16.26]
0.67 [17.02]
0.74 [18.80]
0.74 [18.80]
0.77 [19.56]
0.83 [21.08]
0.83 [21.08]
0.82 [20.83]
0.91 [23.11]
1.10 [27.94]
Sprague
®
T
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.25 [6.35]
0.31 [7.87]
0.34 [8.64]
0.37 [9.40]
0.37 [9.40]
0.44 [11.18]
0.50 [12.70]
0.50 [12.70]
0.47 [11.94]
0.56 [14.22]
0.76 [19.30]
* Parts ordered with D3 leads are standard capacitors in stock and available through the
Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
* 60 Hz rms
ORDERING INFORMATION
225P
TYPE
104
CAPACITANCE
Capacitance is
expressed in
picofarads. The first
two digits are
significant. The third
is the number of
zeros to follow.
Values must
conform to Decade
Rating for the
tolerance specified.
9
1
TOLERANCE DC VOLTAGE
RATING
0 = ± 20 %
9 = ± 10 %
5 = ± 50 %
This is
expressed in
hundred of
volts.
W
CASE CODE
D
TERMINAL
3
LEAD LENGTH
(-XXX)
SPECIAL
CONSTRUCTION
A three-digit suffix
may be added by
the factory to
denote special
construction.
1 = 0.187" ± 0.030"
See Dimensional A = Straight Lead
[4.750 ± 0.762]
Configurations.
B = Hairpin Crimped
D = Hockey Crimped 2 = 0.250" ± 0.030"
[6.350 ± 0.762]
3 = 1.250” [31.750]
Minimum
Note:
Some Part Numbers are in stock and available through the Vishay Sprague
®
Distribution Network. Other Part Numbers are available on
special order through Vishay Sprague
®
Distribution. In the construction of the components described, the full intent of the specification will be
met. Vishay however, reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit
improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Vishay Sprague
®
assumes no responsibility for its use nor for any infringements of patens of other rights of third parties which may result from its use.
www.vishay.com
28
For technical questions, contact: spresale@vishay.com
Document Number: 42016
Revision: 19-Feb-07
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
1
Document Number: 91000
PCB Design
京公网安备 11010802033920号
EEWORLD
