CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1.
θ
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications
Test Conditions: V
CC
= 3V to 5.5V, C
1
- C
4
= 0.1µF; Unless Otherwise Specified.
Typicals are at T
A
= 25°C
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNITS
µA
mA
PARAMETER
DC CHARACTERISTICS
Supply Current, Automatic
Powerdown
Supply Current,
Automatic Powerdown Disabled
All R
IN
Open (ICL3217 Only)
All Outputs Unloaded
25
25
-
-
1.0
0.3
10
1.0
TRANSMITTER INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low
Input Logic Threshold High
T
IN
T
IN
T
IN
V
CC
= 3.3V
V
CC
= 5.0V
Input Leakage Current
Output Leakage Current
(ICL3217 Only)
Output Voltage Low
Output Voltage High
I
OUT
= 1.6mA
I
OUT
= -1.0mA
ICL3217 Powers Up (Figure 4)
ICL3217 Powers Down (Figure 4)
Full
Full
Full
Full
Full
Full
Full
-
2.0
2.4
-
-
-
-
-
-
±0.01
±0.05
-
0.8
-
-
±1.0
±10
0.4
-
V
V
V
µA
µA
V
V
V
CC
-0.6 V
CC
-0.1
-2.7
-0.3
-
-
-
-
100
30
AUTOMATIC POWERDOWN
(ICL3217 Only)
Receiver Input Thresholds to
Enable Transmitters
Receiver Input Thresholds to
Disable Transmitters
Receiver Threshold to Transmitters
Enabled Delay (t
WU
)
Receiver Positive or Negative
Threshold to Transmitters
Disabled Delay
RECEIVER INPUTS
Input Voltage Range
Input Threshold Low
V
CC
= 3.3V
V
CC
= 5.0V
Input Threshold High
V
CC
= 3.3V
V
CC
= 5.0V
Full
25
25
25
25
-25
0.6
0.8
-
-
-
1.2
1.5
1.5
1.8
25
-
-
2.4
2.4
V
V
V
V
V
Full
Full
25
25
2.7
0.3
-
-
V
V
µs
µs
4
ICL3207, ICL3217
Electrical Specifications
Test Conditions: V
CC
= 3V to 5.5V, C
1
- C
4
= 0.1µF; Unless Otherwise Specified.
Typicals are at T
A
= 25°C
(Continued)
TEST CONDITIONS
TEMP
(°C)
25
25
MIN
-
3
±5.0
300
-
-
TYP
0.3
5
±5.4
10M
±35
-
MAX
-
7
UNITS
V
kΩ
PARAMETER
Input Hysteresis
Input Resistance
TRANSMITTER OUTPUTS
Output Voltage Swing
Output Resistance
Output Short-Circuit Current
Output Leakage Current
(ICL3217 Only)
TIMING CHARACTERISTICS
Maximum Data Rate
(One Transmitter Switching)
All Transmitter Outputs Loaded with 3kΩ to Ground
V
CC
= V+ = V- = 0V, Transmitter Output =
±2V
V
OUT
=
±12V,
V
CC
= 0V or 3V to 5.5V
In Automatic Powerdown
Full
Full
Full
Full
-
-
±60
±25
V
Ω
mA
µA
V
CC
= 3.15V, C
1
- C
4
= 0.1µF, R
L
= 3kΩ, C
L
= 1000pF
V
CC
= 3.0V, C
1
- C
4
= 0.22µF, R
L
= 3kΩ, C
L
= 1000pF
V
CC
≥
4.5V, C
1
- C
4
= 0.1µF, R
L
= 3kΩ, C
L
= 1000pF
Receiver Input to Receiver
Output, C
L
= 150pF
t
PHL
- t
PLH
t
PHL
- t
PLH
C
L
= 200pF to 2500pF
V
CC
= 3.3V, R
L
= 3kΩ to 7kΩ,
Measured From +3V to -3V or -3V
C
L
= 200pF to 1000pF
to +3V
t
PHL
t
PLH
Full
Full
Full
25
25
Full
Full
25
25
250
250
250
-
-
-
-
4
6
500
286
310
0.3
0.3
200
100
15
15
-
-
-
-
-
1000
500
30
30
kbps
kbps
kbps
µs
µs
ns
ns
V/µs
V/µs
Receiver Propagation Delay
Transmitter Skew
Receiver Skew
Transition Region Slew Rate
ESD PERFORMANCE
RS-232 Pins (T
OUT
, R
IN
)
Human Body Model
IEC61000-4-2 Contact Discharge
IEC61000-4-2 Air Gap Discharge
All Other Pins
Human Body Model
25
25
25
25
-
-
-
-
±15
±8
±6
±2
-
-
-
-
kV
kV
kV
kV
Detailed Description
The ICL32X7 interface ICs operate from a single +3V to
+5.5V power supply, guarantee a 250kbps minimum data
rate, require only four small external 0.1µF capacitors,
feature low power consumption, and meet all ElA RS-232C
and V.28 specifications. The circuit is divided into three
sections: The charge pump, the transmitters, and the
receivers.
Transmitters
The transmitters are proprietary, low dropout, inverting
drivers that translate TTL/CMOS inputs to EIA/TIA-232
output levels. Coupled with the on-chip
±5.5V
supplies,
these transmitters deliver true RS-232 levels over a wide
range of single supply system voltages.
ICL3217 transmitter outputs disable and assume a high
impedance state when the device enters the automatic
powerdown mode. These outputs may be driven to
±12V
when disabled.
Both devices guarantee a 250kbps data rate for full load
conditions (3kΩ and 1000pF), V
CC
≥
3.0V, with one
transmitter operating at full speed. Under more typical
conditions of V
CC
≥
3.3V, R
L
= 3kΩ, and C
L
= 250pF, one
transmitter easily operates at 800kbps.
Transmitter inputs float if left unconnected, and may cause
I
CC
increases. Connect unused inputs to GND for the best
performance.
Charge-Pump
Intersil’s new ICL32XX family utilizes regulated on-chip dual
charge pumps as voltage doublers, and voltage inverters to
generate
±5.5V
transmitter supplies from a V
CC
supply as
low as 3.0V. This allows these devices to maintain RS-232
compliant output levels over the
±10%
tolerance range of
3.3V powered systems. The efficient on-chip power supplies
require only four small, external 0.1µF capacitors for the
voltage doubler and inverter functions at V
CC
= 3.3V. See
the “Capacitor Selection” section, and Table 3 for capacitor
recommendations for other operating conditions. The charge
pumps operate discontinuously (i.e., they turn off as soon as
the V+ and V- supplies are pumped up to the nominal values),
The reference voltage is like this. If the reference voltage you choose is 5V and your AD is 12 bits, then when your input voltage is 5V, your MCU display should be 4095. If it is 0V input, the value ...
As the title says, how is the 43rd pin GCK0 in this CPLD used? From the name, it looks like a clock pin. Is it an external input or an external clock output?...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:02[/i]I made a platform with 6410, and after a while, it crashed. I don't know why. My HOST USB doesn't have it, but it didn't connect ...
I use TIME2's CH2 to capture input, but the data is incorrect. Could you please help me check if the initialization is correct? Thank you!int main(void){#ifdef DEBUGdebug();#endif/* System Clocks Conf...
I just found a problem. In wince 5, I use EVC to write an application to display an hourglass. The first case is as follows. During initialization, the hourglass is displayed for 5 seconds. The actual...
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
