EEWORLDEEWORLDEEWORLD

Part Number

Search

633L6006I2T

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size905KB,8 Pages
ManufacturerCTS
Environmental Compliance
Download Datasheet Parametric View All

633L6006I2T Overview

LVDS Output Clock Oscillator

633L6006I2T Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerCTS
Reach Compliance Codecompliant
Other featuresSTANDBY; ENABLE/DISABLE FUNCTION; COMPLEMENTARY OUTPUT; TR, 7 INCH
maximum descent time0.7 ns
Frequency Adjustment - MechanicalNO
frequency stability20%
Installation featuresSURFACE MOUNT
Nominal operating frequency60 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
Output load100 OHM
physical size3.2mm x 2.5mm x 0.9mm
longest rise time0.7 ns
Maximum supply voltage2.625 V
Minimum supply voltage2.375 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry55/45 %
Terminal surfaceGold Flash (Au) - with Nickel (Ni) barrier
Base Number Matches1
Model 633
Features
Very Low Jitter LVPECL or LVDS Clock
Ceramic Surface Mount Package
Very Low Phase Jitter Performance, 500fs Maximum
Fundamental or 3
rd
Overtone Crystal Design
Frequency Range 10 – 220MHz *
+2.5V or +3.3V Operation
Output Enable Standard
Tape and Reel Packaging, EIA-418
SerDes
Storage Area Networking
Broadband Access
SONET/SDH/DWDM
PON
Ethernet/GbE/SyncE
Fiber Channel
Test and Measurement
Part Dimensions:
3.2 × 2.5 × 1.0mm
25.00mg
Applications
Standard Frequencies
- 50.00MHz
- 125.00MHz
- 148.3516MHz
- 200.0000MHz
- 155.52MHz
- 156.25MHz
- 161.1328MHz
* Check with factory for availability.
Description
CTS Model 633 is a low cost, high performance clock oscillator supporting differential LVPECL or LVDS outputs.
Employing the latest IC technology, M633 has excellent stability and very low jitter/phase noise performance.
Ordering Information
Model
633
Output
Type
P
Frequency Code
[MHz]
XXX or XXXX
Frequency
Stability
3
Temperature
Range
I
Supply
Voltage
3
Packaging
T
Code
P
L
E
V
Output
LVPECL - Pin 1 Enable
LVDS - Pin 1 Enable
LVPECL - Pin 2 Enable
LVDS - Pin 2 Enable
Code
6
5
3
2
Stability
±20ppm
±25ppm
±50ppm
±100ppm
2
Code
2
3
Voltage
+2.5Vdc
+3.3Vdc
Code
Frequency
Product Frequency Code
1
Code Temp. Range
-10°C to +60°C
A
-20°C to +70°C
C
-40°C to +85°C
I
Packing
Code
1k pcs./reel
T
Notes:
1] Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz, 4-digits for frequencies 100MHz or greater.
2] Consult factory for availability of 6I Stability/Temperature combination.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
DOC# 008-0578-0 Rev. B
Page 1 of 8
©2017 CTS® Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test
equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.
[Serial] [Starlight Lightning STM32F407 Development Board] Chapter 10 Window Watchdog Experiment
[align=center]Chapter 10 Window Watchdog Experiment[/align]10.1 Experimental Purpose This chapter learns the use of another watchdog of STM32 - the window watchdog. For the data sheet, please refer to...
hejecu stm32/stm8
What is the difference between using the same ground for the analog and digital signals under or near the ADC?
The datasheet says that the ground should be connected at the bottom, but if it is connected nearby with a 0 ohm resistor, what problems may arise? I also found that connecting with a magnetic bead ha...
jelly_bessie PCB Design
Voltage selection chart
Could you help me draw a diagram of using a small signal to control the voltage to switch the output? Use transistors or MOS to achieve this, and I hope it is as simple as possible! (Small signal, hig...
hjyouth Analog electronics
Just go---Flirt with the fourth girl... Mountain
[color=#000][font=Helvetica,] [size=5]Time flies by. The Saturday a week ago should have been the weekend, but..., yes, we are still working in the company. After 5pm, I chatted with my colleagues abo...
wajuka Talking
Please recommend: less than 5V input, 200V output DC-DC
Due to design requirements, I want to find a DC-DC with an input lower than 5V and a 200V input. Does anyone have any recommendations?...
7mofnahq Power technology
COTS Power Supplies
COTS products refer to some existing, easy-to-use, and unmodified components. Compared with other systems that can be applied specifically according to special circumstances, COTS systems can save cos...
linkage Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 383  1684  1201  814  2551  8  34  25  17  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号