EEWORLDEEWORLDEEWORLD

Part Number

Search

4M1-SSP1-S3/2M7QE

Description
SLIDE SWITCH, SPDT, LATCHED, 5A, 28VDC, THROUGH HOLE-RIGHT ANGLE
CategoryMechanical and electronic products    switch   
File Size635KB,6 Pages
ManufacturerCarling Technologies
Environmental Compliance
Download Datasheet Parametric View All

4M1-SSP1-S3/2M7QE Overview

SLIDE SWITCH, SPDT, LATCHED, 5A, 28VDC, THROUGH HOLE-RIGHT ANGLE

4M1-SSP1-S3/2M7QE Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerCarling Technologies
Reach Compliance Codecompliant
body width6.6 mm
body height12.7 mm
Body length or diameter10.16 mm
Contact (AC) maximum rated R load5A@125VAC
Maximum contact current (AC)5 A
Maximum contact current (DC)5 A
Contact (DC) maximum rated R load5A@28VDC
Maximum contact voltage (AC)125 V
Maximum contact voltage (DC)28 V
Electrical life30000 Cycle(s)
JESD-609 codee4
Manufacturer's serial number4M1
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
method of packingBULK
sealEPOXY TERMINAL SEALED
surface mountNO
Switch actionLATCHED
switch functionSPDT
Switch typeSLIDE SWITCH
Terminal surfaceSILVER
Termination typeSOLDER
Base Number Matches1
Carling
Technologies
4S & 4M-Series Sub-Miniature & Miniature Slide Switches
4S1& 4SS-Series
Sub-Miniature &
Sealed
Sub-Miniature
Slide Switches
Specifications
Contact Rating . . . . . . . . . refer to ordering scheme
Electrical Life . . . . . . . . . . 30,000 make & break cycles at full
load
Contact Resistance. . . . . . 10 mΩ max. initial @ 2-4 VDC
100mA for both silver & gold plated
contacts.
Insulation Resistance . . . 1000 MΩ min.
Dielectric Strength . . . . . . 1500 Volts RMS @ sea level
Operating Temperature . . . -30°C to +85°C
Solder Heat Resistance. . . MIL-STD-202, Method 210
Actuator Travel . . . . . . . . . 25°
4M1-Series
Miniature Slide Switch
Materials
Case . . . . . . . . . . . . . . . . Dially phthalate (DAP) (UL 94V-0)
Slide Handle. . . . . . . . . . .Nylon
Housing. . . . . . . . . . . . . . .Stainless Steel
Terminal Seal . . . . . . . . . . Epoxy
4S1-Series Ordering Scheme
4S1
-
FSP 1
-
M6 Q E
1
Series
2
Poles
3
Circuit
4
Termination
5
Contact
6
Seal
7
Packaging
1 SERIES
4S1
Sub-Miniature Slide Switch
2 POLES
FSP
single pole
3 CIRCUIT
1
2
3
Switching Position:
2-1
ON
ON
ON
OPEN
NONE
NONE
OFF
2-3
ON
(ON)
ON
5 CONTACT
Material
G
silver
1
K
gold
2
P
silver
1
Q
silver
1
R
gold
2
Terminal Plating
gold over silver
3
tin-lead
4
tin-lead
4
silver
1
gold
2
Rating
3A@125VAC or 28VDC; 1.5A @ 250VAC
0.4VA max. @20V max (AC/DC)
3A@125VAC or 28VDC; 1.5A @ 250VAC
3A@125VAC or 28VDC; 1.5A @ 250VAC
0.4VA max. @20V max (AC/DC)
NOTE:
Tin-lead option available with PC type terminations only.
1
Moveable contact & terminals: copper alloy, silver plate
2
Moveable contact & terminals: copper alloy with gold plate over nickel plate
3
Terminals: silver plate with outer layer in gold plating
4 TERMINATION
M2
PCB
M6
PC Mount, 90° horizontal
6 EPOXY SEAL
E
epoxy seal
7 PACKAGING
Switches are bulk packed, unless
T/R
is specified at the end of the part number.
T/R
tape reel - 500 pieces per reel
46
www.carlingtech.com
Feedback Oscillator Design Tutorial
This paper discusses the design of a basic feedback oscillator, using a lumped element resonator with varactor control. A design center frequency of 1GHz has been chosen, with a tuning bandwidth of 50...
JasonYoo Analog electronics
Analysis of a 12V switching power supply circuit principle
[color=black]This switching power supply is a low-power switching power supply. It inputs 220V AC mains power and outputs 12V DC power. The maximum output current is 1.3A. It is mainly used to power s...
qwqwqw2088 Analogue and Mixed Signal
I need help designing a power module with an input of AC220V, an output of DC 120V, and about 1A
My teacher and I are designing a piezoelectric ceramic drive power supply, which requires a DC 120V voltage. Previously, a senior student used five 220V--24V transformers, then rectified and stabilize...
2841210728@qq.c Analogue and Mixed Signal
About evc development of network card application program
I am a novice, and I need to use evc to develop an application to operate the registers of the network card (the network card is dm9000a wince platform). Can I call the driver function directly or use...
smarsmar Embedded System
Avatar is really charming
A friend gave me two tickets for Avatar that night, so my family of three rushed over. My husband took my daughter to watch the movie, and we waited outside. There were so many people, the movie theat...
向农 Talking
How to configure MSP432 using CCS9 so that code is executed in flash or SRAM?
The power consumption of the code is different when it is executed in different flash or SRAM, but after searching for a long time, I still can't find how to configure the code execution to different ...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1358  2226  868  676  54  28  45  18  14  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号