= 2.7 V to 5.5 V, unless otherwise noted. Temperature range as follows: A version = −40°C to +125°C.
Table 1.
Parameter
TEMPERATURE SENSOR AND ADC
Accuracy
1
A Version
±0.5
−0.87 to +0.82
2
±1.5
±2.0
±3.0
±2.0
±1.87
2
±2.0
±3.0
±3.0
10
800
25
Unit
°C typ
°C max
°C max
°C max
°C max
°C typ
°C max
°C typ
°C max
°C typ
Bits
ms typ
μs typ
Test Conditions/Comments
V
DD
= 3 V @ +40°C
V
DD
= 3 V @ +40°C
V
DD
= 3 V @ −40°C to +70°C
V
DD
= 3 V @ −40°C to +85°C
V
DD
= 3 V @ −40°C to +125°C
V
DD
= 3 V @ −40°C to +125°C
V
DD
= 5.5 V @ +40°C
V
DD
= 5.5 V @ −40°C to +85°C
V
DD
= 5.5 V @ −40°C to +85°C
V
DD
= 5.5 V @ −40°C to +125°C
Resolution
Update Rate, t
R
Temperature Conversion Time
POWER SUPPLIES
Supply Current
3
Peak Supply Current
4
Supply Current – Nonconverting
Inactive Serial Bus
5
Normal Mode @ 3 V
Normal Mode @ 5 V
Active Serial Bus
6
Normal Mode @ 3 V
Normal Mode @ 5 V
Shutdown Mode
DIGITAL INPUT
Input High Voltage, V
IH
Input Low Voltage, V
IL
Input Current, I
IN 7
Input Capacitance, C
IN
DIGITAL OUTPUT (OPEN-DRAIN)
Output High Voltage, V
OH
Output Low Voltage, V
OL
Output High Current, I
OH
Output Capacitance, C
OUT
ALERT Output Saturation Voltage
1.2
900
169
188
180
214
3
mA typ
μA max
μA typ
μA typ
μA typ
μA typ
μA max
Current during conversion
Peak current between conversions
Supply current with serial bus inactive. Part not
converting and D7 of configuration register = 0.
Supply current with serial bus active. Part not
converting and D7 of configuration register = 0.
D7 of configuration register = 1. Typical values
are 0.04 μA at 3 V and 0.5 μA at 5 V.
2.4
0.8
±1
10
2.4
0.4
1
10
0.8
V min
V max
μA max
pF max
V min
V max
μA max
pF max
V max
V
IN
= 0 V to V
DD
All digital inputs
I
OL
= 1.6 mA
V
OH
= 5 V
Typ = 3 pF
I
OUT
= 4 mA
Rev. F | Page 3 of 20
AD7414/AD7415
Parameter
AC ELECTRICAL CHARACTERISTICS
8, 9
Serial Clock Period, t
1
Data In Setup Time to SCL High, t
2
Data Out Stable after SCL Low, t
3
SDA Low Setup Time to SCL Low
(Start Condition), t
4
SDA High Hold Time after SCL High
(Stop Condition), t
5
SDA and SCL Fall Time, t
6
Data Hold Time, t
7
Power-Up Time
1
A Version
2.5
50
0
50
50
90
35
4
Unit
μs min
ns min
ns min
ns min
ns min
ns max
ns min
μs typ
Test Conditions/Comments
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
Accuracy specifications apply only to voltages listed under Test Conditions. See Temperature Accuracy vs. Supply section for typical accuracy performance over the
full V
DD
supply range.
2
100% production tested at 40°C to these limits.
3
These current values can be used to determine average power consumption at different one-shot conversion rates. Average power consumption at the automatic
conversion rate of 1.25 kHz is 940 μW.
4
This peak supply current is required for 29 μs (the conversion time plus power-up time) out of every 800 μs (the conversion rate).
5
These current values are derived by not issuing a stop condition at the end of a write or read, thus preventing the part from going into a conversion.
6
The current is derived assuming a 400 kHz serial clock being active continuously.
7
On power-up, the initial input current, I
IN
, on the AS pin is typically 50 μA.
8
The SDA and SCL timing is measured with the input filters turned on so as to meet the fast mode I
2
C specification. Switching off the input filters improves the transfer
rate but has a negative effect on the EMC behavior of the part.
9
Guaranteed by design. Not tested in production.
SCL
t
1
t
4
SDA
DATA IN
SDA
DATA OUT
t
2
t
7
t
5
t
3
02463-002
t
6
Figure 2. Diagram for Serial Bus Timing
Rev. F | Page 4 of 20
AD7414/AD7415
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
V
DD
to GND
SDA Input Voltage to GND
SDA Output Voltage to GND
SCL Input Voltage to GND
ALERT Output Voltage to GND
Operating Temperature Range
Storage Temperature Range
Junction Temperature
5-Lead SOT-23 (RJ-5)
Power Dissipation
1, 2
Thermal Impedance
3
θ
JA
, Junction-to-Ambient (still air)
6-Lead SOT-23 (RJ-6)
Power Dissipation
1, 2
Thermal Impedance
3
θ
JA
, Junction-to-Ambient (still air)
8-Lead MSOP (RM-8)
Power Dissipation
1, 2
Thermal Impedance
3
θ
JA
, Junction-to-Ambient (still air)
θ
JC
, Junction-to-Case
IR Reflow Soldering
Peak Temperature
Time at Peak Temperature
Ramp-up Rate
Ramp-down Rate
Ramp from 25°C to Peak Temperature
IR Reflow Soldering in Pb-Free Package
Peak Temperature
Time at Peak Temperature
Ramp Rate
Ramp-Down Rate
Ramp from 25°C to Peak Temperature
1
2
Rating
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to +7 V
−40°C to +125°C
−65°C to +150°C
150°C
W
MAX
= (T
JMAX
− T
A
)/θ
JA
240°C/W
W
MAX
= (T
JMAX
− T
A
)/θ
JA
190.4°C/W
W
MAX
= (T
JMAX
− T
A
)/θ
JA
205.9°C/W
43.74°C/W
220°C (0°C/5°C)
10 sec to 20 sec
3°C/s max
−6°C/s
max
6 minutes max
260°C (0°C)
20 sec to 40 sec
3°C/s max
−6°C/s
max
8 minutes max
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Values relate to package being used on a standard 2-layer PCB.
T
A
= ambient temperature.
3
Junction-to-case resistance is applicable to components featuring a
preferential flow direction, such as components mounted on a heat sink.
Junction-to-ambient resistance is more useful for air-cooled, PCB-mounted
[b]When simulating the Zhongying MCU in PROTUES, I cannot find the corresponding component. What should I do? Can I create my own component library like in protel? How can I build my own component lib...
Write Memory error @ address 0x600CAB88, word access: Memory access timeout. Please help me, I am almost dying because of this and I can't debug it....
I will directly attach the IIC controller program that I have recently debugged successfully. I will only post the IIC module because the most important thing in the program is IIC communication, foll...
A low-cost solution for isolated LED drivers is under research and is expected to be released in June this year. By then, there will be a solution that eliminates the need for electrolytic capacitors ...
This is a very classic.... It introduces the establishment of component models in detail... and the super detailed introduction of each power supply model... The most basic things... are not introduce...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
RS-422 and RS-485 are both serial data interface standards, which were developed and published by the Electronic Industries Association (EIA). RS-422 defines a balanced communication interface with a ...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Describe how to meet the challenges of complexity with a modern wiring design toolset. Option codes and expressions can simulate the variables of an automotive project. A full-featured tool suite c...[Details]
At present, a large number of cooling tower fans, speed fans and special fans are in use in petroleum, chemical, pharmaceutical, metallurgical and other enterprises. Some fans have no monitoring in...[Details]
The automotive power electronics market has grown rapidly as comfort and active safety features become more common. As traditional mechanical functions shift to electronic applications, the demand ...[Details]
This article introduces a high-reliability, high-power automatic water supply device made with 89C2051 single-chip microcomputer, which has phase loss detection, over-temperature detection, over-cu...[Details]
At present, more than 40 fieldbuses have been developed in the world, among which CAN bus is suitable for application in automobile inspection lines because of its unique features such as strong re...[Details]
A stepper motor is a motor that converts electrical pulse signals into linear or angular displacements. However, the control of stepper motors is usually developed in assembly language or C languag...[Details]
Today, automakers are integrating more and more complex electronic systems into cars. Allied Business Intelligence predicts that annual sales of the automotive semiconductor market will rise from $...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
