The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
NEW
MS type Lower Profile Plug
H/MS Series
Circular connector conforming to MIL-C-5015
PAT.P
Connector Height Comparison
18-10 Size
50.1mm
45.5mm
3057-10
70mm
54.5mm
Existing MS Connector
Lower-profile Plug
22-22 Size
48.2mm
53.2mm
s
Features
1. 20% Height Reduction
When compared with existing H/MS Series connectors
the overall height of plug assemblies is lower, allowing it
to be used in space constrained applications.
78.7mm
41mm
3057-12
60.7mm
2. Cable Exit in 360° Directions
The cable can exit in any of the 8 fixed direction, in 45°
increments.
Existing MS Connector
Lower-profile Plug
3. Simple Assembly
The 2-piece design consisting of the contact/insulator
assembly and the back-shell assembly allows termination
without the use of any specialized tools.
Cable Exit Direction of 360°
4. Water and Dust Protection
IP 67 rating when fully terminated and mated with
corresponding part.
5. TUV Certification
Provided with a protective circuit function for TUV
certification. The (D) pin is directly connected to the
motors, and a wide variety of industrial and measuring
instruments.
Plug
°
(45
)
Can be changed
in 45 degree increments
45.8mm
63.8mm
56.5mm
18
22
3057-10
3057-12
2004.6
1
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
sProduct
Specifications
Voltage rating
250VAC, 250V DC (pollution degree: 3, overvoltage category:
3)
500V AC, 500V DC (pollution degree: 2, overvoltage category:
2)
Current rating
23A Max. (18-10 size)
46A Max. (22-22 size)
Operating temperature range
-25ç to +125ç
Storage temperature range
-25ç to +125ç
Rating
Item
Specification
18-10 size
22-22 size
Conditions
1A DC
500 V DC
2250V AC/one minute.
Frequency: 10 to 500 Hz, single amplitude of 0.75 mm,
acceleration of 98 m/s
2
for 3 hours in 3 axis.
Acceleration of 490 m/s
2
, 11ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis.
1. Contact resistance
3 m ohms max.
1 m ohms max.
2. Insulation resistance 5000 M ohms min.
3. Withstanding voltage No flashover or insulation breakdown.
4. Vibration
No electrical discontinuity for 10 ms max.
5. Shock
Contact resistance:
Contact resistance:
6. Durability
500 cycles
(insertion/ withdrawal)
4.5 m ohms max.
1.5 m ohms max.
Temperature: -55ç
➝
Room temperature to +125ç
➝
Room
7. Temperature cycle
temperature Time: 30
➝
10 to 15
➝
30
➝
10 to 15 (Minutes)
Insulation resistance: 5000 M ohms min.
5 cycles.
Insulation resistance: 50 M ohms min. (Humidity state)
8. Humidity
96 hours at temperature of 71ç and humidity of 95% .
500 M ohms min. (Dry state)
9. Water/dust
No dust penetration.
When mated with corresponding connector.
No water penetration when submerged for 0.5 hour at the depth of 1 meter.
protection
sMaterials
Item
Body
Insulator
Socket Contacts
Gasket
Bushing
Material
Aluminum alloy
PPS
Copper alloy
Silicone Rubber
Chloroprene rubber
Finish
Black chromate
Color: Black
Silver plating
Color: Black
Color: Black
Remarks
-------------------
UL94V-0
-------------------
-------------------
-------------------
s
Additional Product Information
1. Product number suffixes
(10) Supplied with a wire hole in the locking ring (to prevent loosening of the ring).
(11) Supplied without the wire hole in the locking ring.
2. Corresponding receptacles.
18-10 Size: Part number H/MS3102A18-10P-D-T1(10)
22-22 Size: Part number H/MS3102A22-22P-D-T(10)
2
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
sPlug
H/MS08A18-10S-DT10D(10)
41
A
Ø33.5
D
B
18-10S
C
X
45.5
Part Number
H/MS08A18-10S-DT10D(10)
H/MS08A18-10S-DT10D(11)
H/MS08A18-10S-DT10D1(10)
H/MS08A18-10S-DT10D1(11)
CL No.
120-0476-3-10
120-0476-3-11
120-0481-3-10
120-0481-3-10
Number of Contacts
Weight
4
89g
Ø10~Ø12.5mm
H/MS08A18-10S-DT10C(10)
Ø33.5
35.5
Part Number
H/MS08A18-10S-DT10C(10)
H/MS08A18-10S-DT10C(11)
CL No.
120-0480-0-10
120-0480-0-11
Number of Contacts
4
Weight
77.6g
H/MS08A22-22S-DT12D(10)
A
D
Ø39.5
53.2
Part Number
H/MS08A22-22S-DT12D(10)
H/MS08A22-22S-DT12D(11)
H/MS08A22-22S-DT12D1(10)
H/MS08A22-22S-DT12D1(11)
CL No.
120-0477-6-10
120-0477-6-11
120-0482-6-10
120-0482-6-11
Number of Contacts
Weight
4
127g
Ø10~Ø13.5mm
3057-10
31
Shown one type.
Applicable Cable Diameter Contact solder pot inner diameter
Ø12~Ø14.3mm
2.5mm
41
A
D
B
18-10S
C
X
Ø30
Shown one type.
Applicable Cable Diameter Contact solder pot inner diameter
Ø13~Ø14.3mm
2.5mm
45.8
22-22S
X
B
C
3057-12
36
Shown one type.
Applicable Cable Diameter Contact solder pot inner diameter
Ø13~Ø15.9mm
4.5mm
3
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
B
Assembly Procedures
Process
Outline of assembly
B
B
A
Pre-solder
Conductor portion
A
Contacts
Back-shell
B
Solder
Bushing
1
Insulator/contact assembly
Washer
A
18-10 Size
22-22 Size
24mm
33mm
B
13mm
15mm
Strain relief clamp
a. Pass the strain relief clamp, washer, bushing, and hood over the cable, in this order.
b. Prepare the cable and conductors per the dimensions in Table 1.
c. Bend the exposed conductor to the B dimension as indicated in Table 1.
d. Pre-solder the exposed conductor and solder it as shown to the exposed contact.
Note: Use care not to damage the conductor’s insulation.
4.5 mm min.
Back-shell
Set screw
(Hexagonal hole opposite side 1.27 mm)
3057-10
Locking ring
2
Table 2
Locking Ring
3 to 3.5N • m
Cable Clamp
5 to 6N • m
a. Place over the contact/insulator assembly (in the following order:Back shell, bushing, washer, strain relief clamp).
b. Tighten the Locking ring and Cable clamp to the torque values per Table 2.
c. Tighten the set screw to a torque value of 0.3-0.4 N-m
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
30
57
Table 1
-10
Cable
Strain relief clamp
Screw
Cable
Clamp
Washer
Bushing
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
What knowledge do you need to make a robotic arm model and use a joystick to control simple actions such as rotation, up and down, grabbing, and releasing?...
Consider an example of digital signal processing, such as a finite impulse response filter (FIR). In mathematical terms, a FIR filter is a series of dot products. It takes an input quantity and an ord...
When running the human-computer interaction demonstration program of MSP430G2553, why does the HyperTerminal always show that the COM port cannot be opened?...
I am a beginner in FPGA and I use DE1-SoC to implement a small traffic light program. Modelsim simulation has no problems. The program output includes two parts, one is the countdown displayed by the ...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, this proportion may be as high as 30-40% as more safety electronics, fuel consumption and ...[Details]
With the continuous advancement of various technologies in the field of measurement and control, the baseband subsystem of general measurement and control equipment has entered the fourth generation o...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
