Operating Temperature Range -20°C to +70°C or -40°C to +85°C
Tape and Reel Packaging, EIA-481
Wireless Communications
Broadband Access
FPGA/Microcontrollers
Computer Peripherals
Microprocessors
Test and Measurement
Consumer Electronics
Portable Equipment
Part Dimensions:
11.1 × 4.83 × 4.3mm
•
587.84mg
Applications
Description
CTS ATSSMTS incorporates a high Q quartz resonator in a proven resistance-weld metal package. ATSSMTS offers
tight stability options that are ideal for supporting a wide range of commercial and industrial applications.
Ordering Information
Model
TS
Frequency Code
[MHz]
XXX
Mode of
Oscillation
F
Tolerance
@ +25°C
3
Temperature
Stability
3
Temperature
Range
I
Load
Capacitance
D
Packaging
T
Code
Frequency
Product Frequency Code
1
Code
1
X
2
Y
3
Tolerance
±10ppm
±15ppm
±20ppm
±25ppm
±30ppm
Code Temp. Range
-20°C to +70°C
C
-40°C to +85°C
I
Packing
Code
Tape & Reel
T
Code
F
T
Mode
Fundamental
3rd Overtone
Code
1
X
2
Y
3
5
Stability
±10ppm
±15ppm
±20ppm
±25ppm
±30ppm
±50ppm
2
Code Capacitance Code Capacitance
K
D
8pF
18pF
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
13pF
32pF
B
H
16pF
Series
C
S
Notes:
1] Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz.
2] Check factory availability when combined with -40°C to +85°C temperature range.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
For Flash, the write operation must be performed in a blank area. If there is data in this area, it must be erased before writing. Erasing is performed in blocks. For the FAT32 file system, the FAT ta...
The AT32 F425 is equipped with an RTC timer, which can be used in conjunction with the corresponding functions to realize the RTC timing and timing functions. The operating effect is shown in Figure 1...
Hello everyone, come to "reveal the archives" :pleased:, the fun and rewarding mysterious event I mentioned is here: [url=https://www.eeworld.com.cn/huodong/RIGOL20150310/]https://www.eeworld.com.cn/h...
Hardware introduction: SPI: SPI was first defined by Motorola on its MC68HCXX series processors. It is a synchronous high-speed serial communication protocol. For details about the SPI protocol, refer...
I received the SAM R21 development board yesterday and tried it out immediately. After powering it up via macroUSB, it can be automatically recognized in ATMEL Studio 6, just like other ATMEL developm...
LED glass: The LED light source is embedded between two layers of glass, combined with sandwich-shaped laminated safety glass. The colorful lights are combined into a variety of patterns, which are be...
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
When designing a PLC system, the control scheme should be determined first, and the next step is to select the PLC engineering design. The characteristics of the process and the application require...[Details]
Multimedia applications such as mobile TV, mobile gaming, and audio playback present a huge challenge to power management design in mobile phones. Mobile phone designers need to keep the phone smal...[Details]
1 Introduction
The ball nut is the internal thread element of the ball screw pair. Its precision directly affects the transmission quality of the ball screw pair. Due to its advantages such as...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to be solved urgently. As an important method for detecting automobile ex...[Details]
introduction
This application note discusses power management techniques and methods for calculating power consumption in C8051F00x and C8051F01x SoCs. Many applications have stric...[Details]
Beijing time, June 27, according to foreign media reports, a mobile phone and parts market report recently released by Nomura Securities analysts Romit Shah and Stuart Jeffrey showed that Apple has th...[Details]
Google held the I/O conference in San Francisco on June 27, US time. It is worth noting that the number of devices equipped with the Android operating system has tripled in one year. At this time last...[Details]
An important reason for the low life of LED driver power supply is that the life of the aluminum electrolytic capacitor required by the driver power supply is insufficient. The main reason is that ...[Details]
Abstract:
In view of the characteristics and limitations of traditional hardware radio architecture, the application requirements of analog-to-digital converters in software radio design are ...[Details]
Abstract: The system achieves a low-resistance 50Ω bandwidth of 1 GHz (- 3 dB), a high-resistance 1 MΩ bandwidth of 500 M (- 3 dB) and an attenuation range of 2 mV/div~5 V/div by combining high-speed ...[Details]