EEWORLDEEWORLDEEWORLD

Part Number

Search

AS2578BN

Description
telephone controller with 13 memories and 2-wire bus
File Size280KB,22 Pages
ManufacturerAMSCO [Austria micro systems AG]
Download Datasheet Compare View All

AS2578BN Overview

telephone controller with 13 memories and 2-wire bus

Data Sheet
AS2578 /B
Austria Mikro Systeme International
®
TELEPHONE CONTROLLER WITH
13 MEMORIES AND 2-WIRE BUS
General Description
The AS2578 /B are a versatile repertory LD/MF diallers
with a melody generator, a ring frequency discriminator
and a 2-wire interface to EEPROM. Together with the
AS2520/1, the AS2578 /B form a coherent basis for a
fully electronic telephone with a wide range of options.
The AS2578 /B are especially designed to adapt to
different PTT specifications. A RAM is on chip for last
number redial, 3 direct dial and 10 numbers with
abbreviated dialling. To allow easy use under a PABX,
the device incorporates automatic pause insertion and
sliding cursor procedure as selectable options (AS2578)
or centrex keys (AS2578B). The device can be used with
or without EEPROM as appropriate. When an EEPROM
is connected, all RAM content is stored in the EEPROM
by power loss.
The circuit provides the possibility to set different modes
of operation (LM codes) via the keyboard or via pin
options, e.g. default signalling mode, automatic pause
insertion, flash or ground loop and settings of volume
and melodies.
Key Features
u
u
u
u
u
u
Low operating voltage
Low current consumption, standby
0.1
µA
Oscillator using Xtal or ceramic resonator (3.58 MHz)
Serial interface to external EEPROM
Consistent, simple and usable procedures
The settings are programmed via the keyboard and
stored in EEPROM or set by pin options
Dialler:
Data protection with 20 digit FIFO
Sliding cursor protocol with comparison
Automatic pause generation
Temporary MF select via keyboard
30 digit LNR (Last Number Redial)
13 x 20 digit memory (RAM) on chip
Tone Ringer:
Ring frequency discrimination
3 tone melody with 4 different repetition rates
Volume of melodies can be set in 4 steps
u
u
u
u
u
u
u
u
u
Package
Available in 28 pin DIP and PLCC.
Block Diagramme
Vss V
DD
(AS2578B)
1
4
7
*
2
5
8
0
3
6
9
#
MUTE
SET
LNR
M1
M2
M3
MEM
A
HS
B
C
D
MODE
KEYSCAN
POR
HOOK
STATE
CE
R
3.58 MHz
OSCILLATOR
CONTROL
AP (AS2578 only)
MV
RR
DP
MASK
GL
MUTE
DIAL
REDIAL
DTMF
MELODY
MF
MO
SCL
SERIAL
INTERFACE
SDA
13 X 20
1 X 30
RAM
FIFO
RING
FREQUENCY
DETECTOR
FCI
AS2578 /B
Rev. 3
1
March 1997

AS2578BN Related Products

AS2578BN AS2578P AS2578N AS2578B AS2578 AS2578BP
Description telephone controller with 13 memories and 2-wire bus telephone controller with 13 memories and 2-wire bus telephone controller with 13 memories and 2-wire bus telephone controller with 13 memories and 2-wire bus telephone controller with 13 memories and 2-wire bus telephone controller with 13 memories and 2-wire bus
TI LM3S811 Learning Experience
Record every bit of learning LM3S (Statement: This learning experience is my personal understanding of the notes after studying Zhou Ligong's relevant materials. Due to my limited level, there may be ...
chen8710 Microcontroller MCU
Should the 100uh inductor on the left be a chip inductor or a chip ferrite bead?
Should the 100uh inductor on the left be a chip inductor or a chip ferrite bead?...
electricor Power technology
Who has the highest prestige in EEWORLD?
A few days ago, someone found out in the forum that the richest person is SOSO. So who is the most prestigious person? It won't be SOSO again, right? Let's go to the forum and search it....
tiankai001 Talking
STM32 samples in interrupts. Increasing the interrupt frequency does not increase the sampling rate.
TIM3_Int_Init(4,71);Interrupt frequency setting void TIM3_IRQHandler(void) //TIM3D { if (TIM_GetITStatus(TIM3, TIM_IT_Update) != RESET) //ì2é¨μTIMD·¢éúó·:TIM D′ { TIM_ClearITPendingBit(TIM3, TIM_IT_Up...
无垠星空 stm32/stm8
Why can't I write into the flash of 2812?
After writing the flash of my 2812 chip once, I can no longer write. What's wrong? After connecting to CCS, I click on-chip flash programmer, and the dialog box is all gray. There is only one onlock b...
ssnh6688 Microcontroller MCU
I would like to ask why a resistor should be added to the i/o0 of the microcontroller.
Why do we need to add a pull-up resistor to the pin on i/op.0?...
qixiangyujj MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 438  149  1158  883  2307  9  3  24  18  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号