DATA SHEET
1GB Registered DDR2 SDRAM DIMM
EBE10RD4AEFA
(128M words
×
72 bits, 1 Rank)
Description
The EBE10RD4AEFA is a 128M words
×
72 bits, 1
rank DDR2 SDRAM Module, mounting 18 pieces of
DDR2 SDRAM sealed in FBGA (µBGA
) package.
Read and write operations are performed at the cross
points of the CK and the /CK. This high-speed data
transfer is realized by the 4bits prefetch-pipelined
architecture. Data strobe (DQS and /DQS) both for
read and write are available for high speed and reliable
data bus design. By setting extended mode register,
the on-chip Delay Locked Loop (DLL) can be set
enable or disable. This module provides high density
mounting without utilizing surface mount technology.
Decoupling capacitors are mounted beside each FBGA
(µBGA) on the module board.
Note: Do not push the components or drop the
modules in order to avoid mechanical defects,
which may result in electrical defects.
Features
•
240-pin socket type dual in line memory module
(DIMM)
PCB height: 30.0mm
Lead pitch: 1.0mm
Lead-free
•
Power supply: VDD, VDDQ
=
1.8V
±
0.1V
•
Data rate: 533Mbps/400Mbps (max.)
•
SSTL_18 compatible I/O
•
Double-data-rate architecture: two data transfers per
clock cycle
•
Bi-directional, data strobe (DQS and /DQS) is
transmitted /received with data, to be used in
capturing data at the receiver
•
DQS is edge aligned with data for READs; center
aligned with data for WRITEs
•
Differential clock inputs (CK and /CK)
•
DLL aligns DQ and DQS transitions with CK
transitions
•
Commands entered on each positive CK edge; data
referenced to both edges of DQS
•
Four internal banks for concurrent operation
(components)
•
Burst length: 4, 8
•
/CAS latency (CL): 3, 4, 5
•
Auto precharge option for each burst access
•
Auto refresh and self refresh modes
•
Average refresh period
7.8µs at 0°C
≤
TC
≤ +85°C
3.9µs at
+85°C <
TC
≤ +95°C
•
Posted CAS by programmable additive latency for
better command and data bus efficiency
•
Off-Chip-Driver Impedance Adjustment and On-Die-
Termination for better signal quality
•
/DQS can be disabled for single-ended Data Strobe
operation
•
1 piece of PLL clock driver, 2 pieces of register driver
and 1 piece of serial EEPROM (2k bits EEPROM) for
Presence Detect (PD)
Document No. E0644E30 (Ver. 3.0)
Date Published April 2005 (K) Japan
Printed in Japan
URL: http://www.elpida.com
Elpida
Memory, Inc. 2005
EBE10RD4AEFA
Pin Description
Pin name
A0 to A13
A10 (AP)
BA0, BA1
DQ0 to DQ63
CB0 to CB7
/RAS
/CAS
/WE
/CS0
CKE0
CK0
/CK0
DQS0 to DQS17, /DQS0 to /DQS17
SCL
SDA
SA0 to SA2
VDD
VDDSPD
VREF
VSS
ODT0
/RESET
NC
Function
Address input
Row address
Column address
Auto precharge
Bank select address
Data input/output
Check bit (Data input/output)
Row address strobe command
Column address strobe command
Write enable
Chip select
Clock enable
Clock input
Differential clock input
Input and output data strobe
Clock input for serial PD
Data input/output for serial PD
Serial address input
Power for internal circuit
Power for serial EEPROM
Input reference voltage
Ground
ODT control
Reset pin (forces register and PLL inputs low) *
No connection
1
A0 to A13
A0 to A9, A11
Note: 1. Reset pin is connected to both OE of PLL and reset to register.
Data Sheet E0644E30 (Ver. 3.0)
4
EBE10RD4AEFA
Serial PD Matrix*
1
Byte No.
0
1
2
3
4
5
6
7
8
9
Function described
Number of bytes utilized by module
manufacturer
Total number of bytes in serial PD
device
Memory type
Number of row address
Number of column address
Number of DIMM ranks
Module data width
Module data width continuation
Bit7
1
0
0
0
0
0
0
0
Bit6
0
0
0
0
0
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
Bit5
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
1
0
1
Bit4
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
0
1
0
Bit3
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
1
0
0
0
0
0
Bit2
0
0
0
1
0
0
0
0
1
1
0
0
0
0
0
1
1
0
1
1
0
0
0
0
0
1
0
0
0
0
0
Bit1
0
0
0
1
1
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit0
0
0
0
0
1
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
0
0
0
0
0
Hex value
80H
08H
08H
0EH
0BH
60H
48H
00H
05H
3DH
50H
50H
60H
02H
82H
04H
04H
00H
0CH
04H
38H
00H
01H
00H
01H
3DH
50H
50H
60H
50H
60H
Comments
128 bytes
256 bytes
DDR2 SDRAM
14
11
1
72
0
SSTL 1.8V
3.75ns*
5.0ns*
0.5ns*
0.6ns*
ECC
7.8µs
×
4
×
4
0
4,8
4
3, 4, 5
0
Registered
Normal
Weak Driver
3.75ns*
5.0ns*
0.5ns*
0.6ns*
5.0ns*
0.6ns*
1
1
1
1
Voltage interface level of this assembly 0
DDR SDRAM cycle time, CL = 5
-5C
-4A
SDRAM access from clock (tAC)
-5C
-4A
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
10
1
1
11
12
13
14
15
16
17
18
19
20
21
22
23
DIMM configuration type
Refresh rate/type
Primary SDRAM width
Error checking SDRAM width
Reserved
SDRAM device attributes:
Burst length supported
SDRAM device attributes: Number of
banks on SDRAM device
SDRAM device attributes:
/CAS latency
Reserved
DIMM type information
SDRAM module attributes
SDRAM device attributes: General
Minimum clock cycle time at CL = 4
-5C
-4A
24
Maximum data access time (tAC) from
clock at CL = 4
0
-5C
-4A
0
Minimum clock cycle time at CL = 3
0
-5C, -4A
Maximum data access time (tAC) from
clock at CL = 3
0
-5C, -4A
1
1
25
26
1
1
Data Sheet E0644E30 (Ver. 3.0)
5
51mcu
京公网安备 11010802033920号
EEWORLD
