Table 3. Electrical and thermal characteristics for LUXEON T at 700mA, T
j
=85ºC .
Part numBer
LXH7-FWxx
LXH8-FWxx-x
LXH1-FWRB
ForWard VoltaGe (V)
[1]
mInImum
2.50
2.50
2.50
tyPIcal
2.80
2.80
2.80
maXImum
3.25
3.25
3.25
tyPIcal temPerature
coeFFIcIent oF ForWard
VoltaGe (mV/°c)
[2]
-1.60
-1.60
-1.60
tyPIcal tHermal
resIstance — JunctIon
to solder Pad (°c/W)
3.00
3.00
3.00
Notes for Table 3:
1.
Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.
Absolute Maximum Ratings
Table 4. Absolute maximum ratings for LUXEON T, T
j
=85ºC .
Parameter
DC Forward Current
[1, 2]
Peak Pulsed Forward Current
[1, 3]
LED Junction Temperature
[1]
(DC & Pulse)
ESD Sensitivity (ANSI/ESDA/JEDEC JS-001-2012)
Operating Case Temperature
[1]
LED Storage Temperature
Soldering Temperature
Allowable Reflow Cycles
Reverse Voltage
[4, 5]
(V
reverse
)
maXImum PerFormance
1050mA
1200mA
150°C
Class B
-40°C to 135°C
-40°C to 135°C
JEDEC 020c 260°C
3
LUXEON LEDs are not designed to be driven in reverse bias
Notes for 4:
1.
Proper current derating must be observed to maintain junction temperature below the maximum. For additional information on thermal measurement guidelines please refer to Application
Brief AB106.
2.
Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple”, with frequencies ≥100 Hz and amplitude ≤150mA are acceptable,
assuming the average current throughout each cycle does not exceed the maximum allowable DC Forward Current at the corresponding maximum junction temperature.
3.
Pulsed operation with a peak drive current equal to the stated Peak Pulsed Forward Current is acceptable if the pulse on-time is ≤5ms per cycle and the duty cycle is ≤50%.
4.
Transient reverse voltages and surge currents due to electrical switching or supply interruptions are acceptable if these events do not last for more than 10ms, the amplitude of the reverse
voltage does not exceed 5V and the reverse current is less than 220uA.
5.
Max 5V reverse for up to 10s is an acceptable beginning of life, one time test condition.
I don't understand why the About window procedure in the default project sometimes returns (INT_PTR) type, such as (INT_PTR)FALSE, and sometimes returns TRUE. What's the difference between them? Thank...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:53[/i] In 2007, I was 63 years old. The reason why I want to emphasize my age is that people of my age have personally experienced all the ea...
Please help me, I need help with the design of a microcontroller tracking car. Please provide the program + PCB diagram + schematic diagram. It would be best if the whole one is available. I will be g...
With the continuous evolution of production technology, electronic products tend to develop in the direction of being light, thin and short. Today, various micro-portable electronic products including...
Today, a friend in the forum encountered this problem when posting: some of the codes he sent out were directly turned into emoticons. There are two ways to avoid this problem, for your reference: [b]...
I took the board apart and tested it with a multimeter, and found out the pins of the digital tube. They are common anodes. However, when I wrote the program, the displayed words were not the same as ...