10-Pin µMAX (derate 5.6mW/°C over +70°C) ..............444mW
8-Pin µMAX (derate 4.5mW/°C over +70°C) ................362mW
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Typical
Application Circuit,
V
CC
= +2.7V to +5.5V, T
A
= -40°C to +125°C, 1MHz to 16MHz output frequency range, typical values at
Dear experts, the schematic diagram provided by TI shows that the external 16-bit SDRAM is connected to the CPU's A0 and the SDRAM's A0. Why is it not the CPU's A1 connected to the SDRAM's A0?...
When I was writing a ds1302 program, the following problem occurred : c:/winavr-20100110/bin/../lib/gcc/avr/4.3.3/../../../../avr/bin/ld.exe: cannot find -lC:\WinAVR-20071221\avr\include\avr\io make: ...
After I created a new project, I clicked on the project settings and added the header file to the project (pictured above). I had installed controlSUITE. Then I wrote the following program, following ...
I need help. In the KEIL environment, the peripherals of LM3S9B96 in DEBUG mode are only core peripherals. Other ADC and I/O are invisible. I would like to ask the experts, why is this? I am doing har...
I was looking at the Linux source code recently. I had never touched assembly language before. When I saw the interrupt vector table, I wanted to understand the assembly code. I found that b stands fo...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:11[/i]Have you noticed that, unlike previous national competitions, this year's material list lists electronic switches separately? What type...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
